Search results

Ok so my son just bought a 2015 with Boost it turbo and I have a backfire on a climb and just runs ****ty most of the time I am thinking it’s nothing to do with turbo but may be wrong. On a pull at about 7800 rpm it starts to lose power and then backfires. I have fresh fuel in it checked over...

Just wondering if anyone has used the 531 belt for the 2018 G4 on a XM yet or any info on using them on the T3

I have a 2016 T3 174 and going up trail at Revy it kind of sputters and hesitates at mid range when you hammer on throttle .Once im up top it never misses a beat. Had a Mbrp can on it and now I have TSS tunnel dump ad no difference. Anyone have or cured this issue Thanx Bob

So I put a new ECM and Dess key that were a matched set in my sled and it starts and runs fine but cluster just reads RPM. When I first start sled gauge tests out fine then just RPM will read and Engine light is on and Dess light is flickering. Do I have to get the gauge programmed to ECM Thanx

What is a person suppose to seal crankcase halves with when doin a crank. Have heard of lots of differnt ones.2009 800r Thanx Bob

Does anyone in Alberta stock the 872R Cylinders or do all the dealers just sent to Dave to be done as they get a order Thanx

Does anyone know if a rev 07 secondary splined shaft will fit on a 08 xp Poor mans conversion to a team clutch lol Bob T 403-598-6825

Ok so i put a 2010 800r in a 2007 rev and kid rode about a hr and now as engine idles down it starts knocking.Doesnt do it every time Sounds like pto side bottom end to me but when i had apart to put new Rk tek dual ring pistons in bottom end felt tight.Engine has about 850 miles.No sign of...

I just bought 07 summit X with a 800R Ptek and am wondering if a 2010 Summit X 800R PTek motor will fit. I understand the 07 base plate will need to be used but from what im seeing from pictures is that bottom plate on 2010 comes off and mounts to 07 base plate whicH is also the mounting...

Ok so i am putting Team secondary on 09 XP 860 with TRA primary and would love some tips on alignment or should i just be ordering alignment tool from slp.Red Deer Powersports can order me one in but would be 8-10 days and 130 bucks. Problem is Cariboo opens in 7 days.

I have 09 860 that overheats all the time on way up trail.Blew crank up and had a complete rebuild on motor and still overheats.Could this be related to the ecm recurve being very aggressive. I have 174 2 1/2 but was same issue with 154 i had on it.I had new tunnel cooler built by Van Amburg...

Does anybody know if someone in Calgary sell the pto bearing buddy for xp 800 Thanx Bob

Wondering if 2013 spindles will fit onto my 09 I have seen some posts on other sites but cant fiqure out what everyone decided.So will they just fit right on with out any changes or what. I wrecked mine so need to put new ones on so thought may aswell update to newer style. Thanx Bob

What are good readings for Air Fuel ratio on 2 strokes.Have 860 I put one on and wanna have some close numbers to work with. Thanx

Does Dyno port make a 860 pipe or is it just a 800 pipe.Dyno port website doesnt list 860 pipe. Thanx

Just bought a 2003 summit 800 ho and we were in revy on weekend and everytime my kid tipped his sled on its side when he was carving in the pow it would flood out and would get fuel up into DPM manifold.Would actually have to pull plugs and air cylinders out and replace plug to get running.Is...

When everyone talks about crank pilling up on these 800r what is failing.Is it main bearings or rod bearings.The reason i ask is my motor blew this weekend and when i pulled apart mag piston is leaned burned and rod is blue and rod bearing is very rough.PTO side looks perfectly fine.Is it...

Hey was wondering what type of riding is in the York area Thanx in advance

Does anyone know the best and cheapest place to buy a challenger Extreme 16+163+2.5+2.86 for an 08 xp in Alberta.My stocker is ripping surprise surprise and would like to upgrade Thanx:

Does anyone know where to get a Rkt head in Alberta for A 08XP 800R Thanx