Search results

Was wondering if I should get a GGB quiet can or SLP silencer or Bikeman full velocity muffler for 850 Polaris. What do you guys think and experiences with any of them. TIA.

New 850 Polaris rmk pro brakes are dragging but when I crack the bleeder they unstick, so I took the cap off of the master cylinder and when I squeeze the brake lever then release it the master cylinder does not burp back fluid out of the one master cylinder hole cause I checked on another...

Riding and noticed a slight rattle noise which seems to be in the motor so stopped looked things over to see if maybe spring off muffler and stuff like that, seemed all good. Started to ride again no rattle until motor was warmer shut it off waited then started riding again no rattle until about...

Mbrp can off of a 2007xrs rev I think it will fit all rev chassis $40 obo. The outlet part is a bit bent see pic. I think I used it for maybe one season.

Anybody sled July 1st, any pics?

Was looking on polaris parts for oem primary clutch weights for 2017 800 axys with a 163 and it says 10-64 weights, Then I checked 2020 800 with 163 and it says 10-66 weights. Wonder if for my 2017 I should get the 10-64 weights or the 10-66 weights anybody have any opinions what would be...

Plan on getting a type 1 septic system installed with drain field. Was wondering do you think it's ok to get it put in even though I am not sure of the exact location of the house I will get built, and if I do get the system installed now I wouldn't be using it or building my place for like 5 years.

Where the stator wire comes out and touches the coolant line the casing around the stator wires wheres a hole in it exposing the wires plus will eventually wear a hole in the coolant line check yours out. This is for the 800 axys.

Wondering lost papers registration etc for sled hiw do i get a copy of it. Do i just go to icbc with serial# and then they can give me a copy how much $ im in british columbia.

Wondering where to buy a complete primary clutch tool set puller bolt,spider tool, jam nut tool clutch compress tool, clutch holding tool. Off of the internet would be easiest for me. Its for an axys 800 sled. Tia.

I removed my driven clutch to clean it. I noticed in behind the clutch (between the clutch and jack shaft bearing there is only one of the 16gauge bushing washers (the thick one) in the manual it says you should have at minimum one .120 washer, so do you think i should add one of those to, i...

Does any one know if it is normal to be able to move the bolt back and forth that goes through the weight, attached pic of bolt i am talking about, the other two dont move side to side. If amybody knows what or if this is something wrong that would be cool.

I have a stock main pipe off of a 14xm and stock ypipe never used them took them off when i bought the sled brand new anyway want 350 for both

Just wondering when does the warranty expire on a snowcheck 2014xm, bought in 2013 in october. i know its this year but not sure exactly what month it ends. TIA.

I can't remember been awhile since I have worked on the xrs. Anyway none of the gauges work they did then hit s bump really hard and everything quit no tach no speedo no trip metre or odometer. Still starts though and seems to run good, could it be voltage regulator? Or when I was looking...

I have 14xm that has the slp exhaust kit, whick includes ypipe, main pipe, and muffler. Does anybody know or have an opinion if my engine warranty will still be covered for example if it blows up (piston failure), or if my crank runout is out of spec will dealer still replace crank and be...

Just wondering how people tighten the 2 inner bottom ypipe bolts on xm ski doo.

Was wondering does anybody here bring there ipad mini with them when sledding. Mine has the protective case just want the bigger screen for pics and videos etc.

I am rebuilding a 2007xrs, i have a 2010 monoblock cylinder on an 0& bottom end that is all good, the problem is the 2010 monoblck cylinder the holes where u bolt the y pipe are bigger so i was thinking i will just drill out my ypipe to accommodate the bigger allen bolts well not that easy as...

I am currently replacing the monoblock cylinder i am replacing the 08 monoblock cylinder with a 2010 reman monoblock cylinder the 08 is fubarred. I c the y pipe bolts are bigger that is no problem. But i also noticed where u bolt the raves 2 the cylinder there is a small hole through the...