Your in line boost controller will only allow you to turn your boost down to the value of the spring in the wastegate which is set by turning your wastegate rod in or out. Shortening the rod increases spring value/higher wastegate setting, more boost. Decreasing rod length decreases spring...
you could try unplugging all your wiring input/outputs to your handlebars, should be behind the aluminium shield below your handlebars. This would eliminate your throttle sticking sensor as well as your reverse switch. I had a problem with my rer trying to come on when I shouldn't, engine...
I wouldn't worry about the diamond drive they have a lot of play when you move the secondary, there are a lot of planetary gears that each have a little clearance. Also a good reason to not get rammy between forward and reverse. If you run out of options you could try and look at your reeds...
Team Dirt is a stand up guy who puts his own personal time in to ensure all you (appreciative riders) have a place to ride. I watched the video and thought the same thing he did. I live in B.C where groups are looking for any excuse to eliminate motorized use of all areas. Its already...
I have purchased products from Wayne (Menz Toys)as well. Great customer service and vent kits were excellent. Support your local vendors or they won't be there.
I would be thinking that your reeds are done. I have a 2010M8 with 2000miles on it, every 1000 miles I have had to replace the reeds I'm on my 3rd set of stockers, tipps wear off and or pieces break off. What I noticed was engine loading up when going down long hills when your not on the...
Great news on the pooch and truck. Sucks the deck is gone but all that really matters is that the dog is back home, at least they left the truck running to keep Sarge warm.
My buddys White Ford F350 4x4 4 door short box with a brand new bulldog deck was stolen from Aberdeen mall in Kamloops today with his black lab(Sarge) of 12 years still in the truck. All he wants is his dog back !!!!!!!! Truck plate number is DY 6453 and the black lab is Sarge, he has a silver...
My buddys White Ford F350 4x4 4 door short box with a brand new bulldog deck was stolen from Aberdeen mall in Kamloops today with his black lab (Sarge) of 12 years still in the truck. All he wants is his dog back !!!!!!!! Truck plate number is DY 6453 and the black lab is Sarge, he has a silver...
So I have had this 25 Horse susuki tripple outboard that won't run properly. I have had it into two susuki repair shops and they thought they fixed it but they didn't. If anyone has any recomendations on a decent repair shop Id be interested. I'm in Kamloops but I'm willing to do a little...
Re: Ass hats at Mustang Powder
I wasn't blaming Albertans if that is what my post has led people to think. I ride a lot of areas and know that people from BC and everywhere else are equally as guilty of doing stupid ch!t like this, stupidity and ignorance seems to be equally distributed...
Thanks to all the people who left beer cans all over the trail up to mustang powder. I'm sure Mustang Powder appreciates it come summer. Good job on making sledders look like a bunch of jackasses in a time when we are having troube keeping existing areas open let alone sledding on Cat skiing...
I'm running the stock can/suitcase on my 2010 M8 and was wondering about installling the side vent kit on that side, it seems that the vent screening will be really close to the exhaust. Has anyone installed a a vent kit on this side, did it melt or is there enough air exchange to keep it...
Here's my two cents, I run a dodge 3500 with fog lights, I had them enabled so they come on with my high beam lights and turn off when I go to low beam. I had the dealer do this, for people with programers they can do this themselves. As far as I know this is legal, I have some DOT...
I have a 2010 M8 and after having read all the forums and looking at it the problem on my own sled it's the tunnel is too narrow as stated on other threads, its forcing the drive shaft against the diamond drive loading up the bearing. You can put any bearing you want in there, as a mechanic...