Search results

  1. O

    Etec Can on Ptek

    Could I use an can from Etec on a Ptek if I plug port? Thanks
  2. O

    Mountain days are over.

    Should I replace cylinders as well. Anyone local to buy from?
  3. O

    Mountain days are over.

    Looking at 2014 800 Etec now. 6300kms. Should I be concerned?
  4. O

    Mountain days are over.

    Looking at either 600 summit sport or 600 renegade etec. Plan to use around lake. Taking granddaughter for rides, but also want ability to play in the snow. I've looked into a 2 up seat kit and adding electric start to sport, so that is not an issue. Having just sold my 800 XP, I do not need...
  5. O

    Need Help After carb cleaning.

    Found problem. Read a post regarding same problem. Power wire to battery under boot wasn’t hooked up. I had put a new battery in and must have missed small wire. Oops! That to all that read post. Question. Do i need to take to dealer to Hookup to Bud?? thanks
  6. O

    Need Help After carb cleaning.

    2010 XP Removed carbs to clean. First go at it and ended up removing fuel tank and related parts to do it. Reassembled except no covers. Nothing on elec start, no flicker on pull start. Checked all connections. Fuses beside solenoid good. Upper two fuses no current either side. Disconnected...
  7. O

    Sled Deck Ramps Concerns

    Are they for sale?
  8. O

    Sled Deck Ramps Concerns

    Do you use winch at all?
  9. O

    Sled Deck Ramps Concerns

    Just to clarify, quad was in 4x4. And measurement for rear are outside to outside. Any video I watched, the wheels of the ATV were inside outer edge of ramp. I believe Marlon ramps are 55" and Crosstrax is 52". X Deck ramp non issue for sleds. Was hoping to hear from any X Deck owners and their...
  10. O

    Sled Deck Ramps Concerns

    Son in law just purchased a X Deck. Had a little adventure loading CanAm 800 ATV. Not sure of his tire size but they have an aggressive tread and the backs are a bit wider. What happened is his quad got half way up, and from what we can analyze his right rear spun out and front came up and off...
  11. O

    Belt wear 2010 XP

    Thanks for comments. Clutches are off for cleaning and inspection. I will check mounts, and alignment after reinstalling. Crank run out was .003".
  12. O

    Belt wear 2010 XP

    Please advise possible cause of this. Belt cogs are glazed on outer edge of belt towards outside , only torn in this small area.
  13. O

    Clutch Kits

    Have read lots of comments re DJ, Cudney, Roosterbuilt and SPI clutch kits but not much about Goodwin. Anyone have any thoughts about Goodwins Kits?
  14. O

    What happened?

    Thanks to everyone for all the great feedback and information. As for the son-inlaw? He owes me big. haha
  15. O

    What happened?

    Any shops in south Edmonton for parts and machining?
  16. O

    What happened?

    If stuck thermo or n/g oil pump would we not see damage to both? Thanks
  17. O

    What happened?

    2001 800 summit, 3000km Only had about 3 hours this winter. Son-inlaw took to mountains, 2 miles from staging siezed up. Tore down tonight, flywheel side cylinder scored. Rings not broken, plugs nice and brown, piston domes look good, nothing jumps out. First time tearing 2 stroke apart. Boots...
  18. O

    Everest or X

    Thanks for all the great input. Just picked up 2010 X. Pumped to get on the snow!:d
  19. O

    Everest or X

    Thanks for the input, another twist 09 or 10? Much to gain/lose? Thanks
  20. O

    Everest or X

    Looking to buy. Im an average rider. Other than shocks, gauge panel and some lighter parts is there anything to gain buying a X rather than a Everest? 2010 model Thanks
Top Bottom