DaveB
Active VIP Member
The Kitty would blow off the PZeros at any speed under 80-90kmhr. With the 555R2s I can mash it after 2nd and it hooks. From a dead stop and anywhere in 1st gear still requires a gentle touch on the throttle.
What Did You Do In Ur Garage?
- Thread starter OVERKILL 19
- Start date
The Kitty would blow off the PZeros at any speed under 80-90kmhr. With the 555R2s I can mash it after 2nd and it hooks. From a dead stop and anywhere in 1st gear still requires a gentle touch on the throttle.
Beer Slayer
Active VIP Member
Working on a proto-type mobile pressure washer...still waiting for a cam lock that's on order. [tank to pump]
Obvious it not a JD, but it had to be painted, lol.
Probably never fill due to the weight, 250 gals/1000 liters. The price was right on the tote.
Plan is to wash travel trailers for sale that are parked close to the road that get covered in road debris.
...we'll see?
Obvious it not a JD, but it had to be painted, lol.
Probably never fill due to the weight, 250 gals/1000 liters. The price was right on the tote.
Plan is to wash travel trailers for sale that are parked close to the road that get covered in road debris.
...we'll see?
Attachments
Lightningmike
Active VIP Member
Well it's been about 9 days yo get ti this point in my old garage. There was only a couple paths to walk in when I started. What a mess. I put a wall down the middle and 1 side is cold storage and the other side will be a wood working room.
I think I will get some puck board for benches as well and can cut meat after successfull hunting seasons as well.
Picked up a wood heater to put in corner.
I think I will get some puck board for benches as well and can cut meat after successfull hunting seasons as well.
Picked up a wood heater to put in corner.
Attachments
Lightningmike
Active VIP Member
Bench is 18' overall. Will probably put another one on other side and try and incorporate my table saw in it
kingcat162
Active VIP Member
Put a koso x2 gauge on an m1100 and an electric rollover valve
- Moderator
- #666
Looking online, to get some new garage prices. Would like to go 30x30 but don't know if the city will allow us?
I guess we find out when we get serious about a builder.
Speaking of which...... Any recommendations for a garage builder in Calgary? Looking for one to do job, start to finish.
I guess we find out when we get serious about a builder.
Speaking of which...... Any recommendations for a garage builder in Calgary? Looking for one to do job, start to finish.
struglin
Active VIP Member
I’ve used Reggie from garage builders on a couple, they always come through on time worth a call.
Rhodesie
Active VIP Member
Lightningmike
Active VIP Member
Shiny!
kingcat162
Active VIP Member
New lights on the 2 stroker and a lithium battery with a master kill
rsmorin1
Active VIP Member
Put the winter tires on the wife’s suv & installed airbags on the Ram 2500 diesel. Might be the last nice weekend for a while!
- Admin
- #672
Went by Brianh’s house he was starting to put his motor in his g4 skidoo
meierjn
Active VIP Member
I pulled the sleds out of the corner and fired them up. It was good to smell the 2 Stroke again! I carefully put everything back and positioned the bikes and even managed to get our vehicle in for the night. I hate to say it but I should have dug out the Christmas lights this weekend and got a start on putting them up!
mclean
Active VIP Member
SUMMIT TREE
Active VIP Member
Thats sweet!
Where do buy different kinds of “fancy” wood?
Where do buy different kinds of “fancy” wood?
pipes
Active VIP Member
Windsor Plywood.
mclean
Active VIP Member
Windsor Plywood is correct. I'd love to find somewhere cheaper with rough cut lumber but haven't managed to yet.
They are very simple to make. Quite rewarding once you dump some oil on them and everything pops
They are very simple to make. Quite rewarding once you dump some oil on them and everything pops
Grinder
Active VIP Member
Try a private mill
Similar threads
