Search results

Looking at muffler/can options. Redline is local and cheap. Anyone try it?

shortly after putting a high elevation pipe on, my egt failed. Replaced with working used one and it lasted a day. Same code. would I be smart to go back to stock pipe and try again? or is the sensor ruined and I need to replace anyway?

So I installed jaws single pipe on my 16' axys 800 with 155 3" track. I have a 120-340 primary spring for little higher finish, otherwise stock clutching (eg. 64gr weights). I only hit 8100 rpm in the mountains and Jaws recommends 8400. Any experience with this pipe and what are you...

Hey everyone. seems I ended up 2 pieces short on my sled deck / ramp restore project. Wondering if anyone has 2 spares they would sell. Won’t need the screws as these last 2 are to finish the ramp. Enjoy the snow out there! j.

Hey, i have two Axys tracks to clip. Have all the clips but need to find a tool. Hoping not to have buy a new one. Anyone have one they are finished with? sell used? rent? trade for beer? No rush yet but figured it would be a good time to start asking. thanks.

I am thinking of welding a couple support pieces for my track/skid. I have see the odd one but never got a chance to look closely. Didn't MLine make some too? My loading bar is square (STF) so shouldnt be too hard to fab. Any pictures of your design?

so my starter gear has ground down and wont engage the primary. when looking at the parts list I see tow parts: the assembly for $225 and spring, bendix for $26. I read somewhere the polaris doesn't sell just the starter gear and I cant find pictures of what is included in the $26 part. is...

I have never tried, nor do I know anyone who has. independent of the quick drive vs. chain case discussion, what are you experiences with a 155x3"? and how might it differ from a 163x2.6" this might not be a simple question (snow conditions etc..) thanks.

Hi. About to put a tunnel wrap on an older sled that has an oxidized tunnel. It was previously polished then sat in a trailer for 3 years. I don’t want to be disappointed so looking for experience on how to clean/prep the aluminum before I apply vinyl. I did get the application Kit but...

Hi. Seems I need new bearings throughout my skid (2011 pro rmk). Where does everyone get theirs? and which suffix to get LU vs 2RS? Mine appear to be LU but the RS bearing seem more available. Important difference? regards.

Just curious. I am running 19/43 and am considering lower. 44-45 is the obvious choice but then i'm into a new chain too. Just wondering if anyone has done 18/...

anyone know where I can find some in Edmonton? Puttin a new fuel pump in and different filter. Would like to update fule lines as well just incase (chasing a low fuel pressure problem).

has anyone changed o'rings on their fuel check valve? It's a harley and what was once a drip is now a stream of fuel. I"m not happy as I changed my whole check valve last year. Are those orings annual changes? any advice or help greatly appreciated. if you have one of those fancy tools to...

So at 1700 miles my 2011 pro has developed it's very first hiccup. At wide open throttle it will bog and the engine light is on. I can work it up to 8000 rmp on the trail or lake without bog as long as I keep the throttle away from the bar. I can work the throttle in the hills and trees...

Need new rubber for trailer (20.5-8-10 or similar) I checked Princess auto with no luck. Any recommendations on where else to look? Also open to alternate sizes that will fit on the rim, or tire rim combos if found on sale. I wouldn't complain if I put a slightly taller tire on as it will...

anyone know where to buy mill ends in Edmonton? I've been to BusyBee, any place else? thanks.

I'm not at all familear with local bike shops or what can even be done but my bike has quite a dent in the tank after laying it down the other day (to avoid a school bus that was skidding sideways on Wayne Gretzky). A few bolt on parts are required but a new tank is insane expensive. Any advice...

hey guys, planning a ride with the kid tomorrow afternoon and just realized his chain is seized. Where could a guy find a 420 chain on a sunday? any one have a spare from a dirtbike or something they will sell?

So, if I were to change my chaincase oil, how do I fill? Tip the sled ? I don't see anywhere I can fill the oil... there is a tiny line coming out just over the chain tensioner, would that be it? thanks

so the gas gauge on my RMK has recently been reading empty all the time. my float sinks. I compared the float with a buddies and mine weights 16g, vs. his that is only 9g. Can these things somehow get waterlogged? are they hollow? can I buy just the float that runs on the gauge? So many...