99 700 rmk idle screws

JZ1

Active VIP Member
Joined
Dec 11, 2013
Messages
421
Reaction score
323
Location
Drumheller
Would the screw with the black plastic head and spring on the left side of each carb be the idle screws? If so how many turns back from slightly seated should they be? I do have the manual for the sled and it doesnt say squat.

Also what height should the slides be set at?
 

Rbrduk

Active VIP Member
Joined
Mar 27, 2012
Messages
11,097
Reaction score
8,465
Location
Dickson,AB
Would the screw with the black plastic head and spring on the left side of each carb be the idle screws? If so how many turns back from slightly seated should they be? I do have the manual for the sled and it doesnt say squat.

Also what height should the slides be set at?
I believe they should be set at 1 1/2 turns out from fully seated.
I just sold mine before xmas with the manual but will try to get you a picture of the pages you need.
 

JZ1

Active VIP Member
Joined
Dec 11, 2013
Messages
421
Reaction score
323
Location
Drumheller
I believe they should be set at 1 1/2 turns out from fully seated.
I just sold mine before xmas with the manual but will try to get you a picture of the pages you need.

i do have a manual but i could not find any specs. ill double check but if you could get a picture that would be great.

i fairly new to this but when i go to fully seat the screws i should do so with the throttle wide open correct?......and sled turned off of coarse lol
 

Rbrduk

Active VIP Member
Joined
Mar 27, 2012
Messages
11,097
Reaction score
8,465
Location
Dickson,AB
i do have a manual but i could not find any specs. ill double check but if you could get a picture that would be great.

i fairly new to this but when i go to fully seat the screws i should do so with the throttle wide open correct?......and sled turned off of coarse lol

I will double check but I think it's with throttle closed.
I had a shop manual, so a little more info.
 

JZ1

Active VIP Member
Joined
Dec 11, 2013
Messages
421
Reaction score
323
Location
Drumheller
I will double check but I think it's with throttle closed.
I had a shop manual, so a little more info.

Im probably wrong but my thinking is with the throttle closed would the screws not dig it the slides while screwing them in?
 

Rbrduk

Active VIP Member
Joined
Mar 27, 2012
Messages
11,097
Reaction score
8,465
Location
Dickson,AB
Im probably wrong but my thinking is with the throttle closed would the screws not dig it the slides while screwing them in?

No, there is a cut out on that side of the slide.
 

Rbrduk

Active VIP Member
Joined
Mar 27, 2012
Messages
11,097
Reaction score
8,465
Location
Dickson,AB
The screw doesn't hold the slide up. This is set with a gaping tool to sync the carbs.
 

JZ1

Active VIP Member
Joined
Dec 11, 2013
Messages
421
Reaction score
323
Location
Drumheller
So what exactly do these screws do?
 

007sevens

Active VIP Member
Joined
Nov 24, 2009
Messages
20,963
Reaction score
16,976
Location
At my Place in Alberta
Would the screw with the black plastic head and spring on the left side of each carb be the idle screws? If so how many turns back from slightly seated should they be? I do have the manual for the sled and it doesnt say squat.

Also what height should the slides be set at?
there is no set amount of turns. I have set my carbs by looking at the slides through the throttle bodies while the air box is off. You will need to (with the engine off) open and close the slides each time after adjustment. I let them slam down from full throttle. adjust them so you think they are equal. Start the sled and see where your Idle is. If its to low adjust them equally from that there.
 

Rbrduk

Active VIP Member
Joined
Mar 27, 2012
Messages
11,097
Reaction score
8,465
Location
Dickson,AB
Here is the info
gy7anyva.jpg
 

moyiesledhead

Active VIP Member
Joined
Oct 12, 2008
Messages
5,452
Reaction score
10,875
Location
Moyie B.C.
there is no set amount of turns. I have set my carbs by looking at the slides through the throttle bodies while the air box is off. You will need to (with the engine off) open and close the slides each time after adjustment. I let them slam down from full throttle. adjust them so you think they are equal. Start the sled and see where your Idle is. If its to low adjust them equally from that there.

That's half the job. After that you need to adjust your cable adjusters so that both slides start to lift off idle at the same time.
 

JZ1

Active VIP Member
Joined
Dec 11, 2013
Messages
421
Reaction score
323
Location
Drumheller
So what am I measuring from for throttle gap and idle gap, also what's the difference between the two?
 

moyiesledhead

Active VIP Member
Joined
Oct 12, 2008
Messages
5,452
Reaction score
10,875
Location
Moyie B.C.
So what am I measuring from for throttle gap and idle gap, also what's the difference between the two?

I never measured anything, just did it by eye. The CORRECT way to do it would be with vacuum gauges on both carb bodies, but doing it by eye always worked just fine for me. Just get your idle right, then check they're both open the same amount at idle. Once you get that set then just push your throttle ahead with the engine OFF and watch the slides. Adjust the cable adjusters so that both start to lift at the same time. Pretty easy really.
 

JZ1

Active VIP Member
Joined
Dec 11, 2013
Messages
421
Reaction score
323
Location
Drumheller
I never measured anything, just did it by eye. The CORRECT way to do it would be with vacuum gauges on both carb bodies, but doing it by eye always worked just fine for me. Just get your idle right, then check they're both open the same amount at idle. Once you get that set then just push your throttle ahead with the engine OFF and watch the slides. Adjust the cable adjusters so that both start to lift at the same time. Pretty easy really.

Is there not a correct height though to set the slides at?
 
Top Bottom