Is there any interest?

Longhairfreak · Nov 21, 2019

I have a complete right down to the clutches Engine Tech 900 based on the Polaris 800. Comes with Jaws 1404 pipes. Even has the 97 700 ignition with a new stator. Was thinking of selling if there is interest. 180 hp and 116 ft lbs torque. Needs pistons or crank haven't taken apart yet.

Longhairfreak · Nov 26, 2019

Just had a look needs 1 piston.

pipeliner72 · Nov 26, 2019

No thanks I prefer to buy my boat anchors at cabelas!

Bnorth · Nov 26, 2019

will it bolt into my ascender chassis?

kanedog · Nov 26, 2019

How much does a broken piston motor go for these days?

Longhairfreak · Nov 26, 2019

kanedog said:
How much does a broken piston motor go for these days?

$2000

Longhairfreak · Nov 26, 2019

Bnorth said:
will it bolt into my ascender chassis?

It would but it would be a lot of work.

Longhairfreak · Nov 26, 2019

pipeliner72 said:
No thanks I prefer to buy my boat anchors at cabelas!

I'd like to see your ride.

Bnorth · Nov 26, 2019

Longhairfreak said:
It would but it would be a lot of work.

I'm interested in bolt in only

Chrisco · Nov 26, 2019

That the same engine I spanked with my 900 cat twin in my Polaris edge back in 2000 ?

Longhairfreak · Nov 26, 2019

Chrisco said:
That the same engine I spanked with my 900 cat twin in my Polaris edge back in 2000 ?

Not a phuking chance. This was a 2006 build. I didn't know that you had a Polaris Edge in 2000. Were you some kind of Polaris tester for the up and coming? Did you have any involvement in the 900 Polaris? How many 1160s did your Polaris big bore spank? Were you a belt drive guru for Polaris? Did you have any involvement with Polaris on gluing sleds together? Were you an integral part of the Polaris track testing?

banditpowdercoat · Nov 26, 2019

I'm interested in a cool coffee table.

Longhairfreak · Nov 26, 2019

banditpowdercoat said:
I'm interested in a cool coffee table.

Talk to Chrisco.

Longhairfreak · Nov 27, 2019

If Chrisco had an Edge in 2000 he must have been a Polaris engineer for one of the worst sleds Polaris built.

deaner · Nov 27, 2019

I am very interested. Would this bolt into an rx1 chassis without too much modification?

banditpowdercoat · Nov 27, 2019

Longhairfreak said:
Talk to Chrisco.

Has to be turn key... lol

kanedog · Nov 28, 2019

Is this still available?

Chrisco · Nov 28, 2019

Ur right sorry my mistake it was my Gen II first and then my Edge after that. That 1160 billet belt blower could never hold a belt for more than 5 minuets.

Longhairfreak · Nov 28, 2019

Chrisco said:
Ur right sorry my mistake it was my Gen II first and then my Edge after that. That 1160 billet belt blower could never hold a belt for more than 5 minuets.

Actually my 1160 was the first 1160 to stop blowing belts.

Longhairfreak · Nov 28, 2019

kanedog said:
Is this still available?

It is.

Is there any interest?

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Attachments

Active VIP Member

Active VIP Member

Similar threads