DRD
Active VIP Member
There goes the Duke fund...
Gonna drive it on the street?
Gonna drive it on the street?
Shipping and importing a vehicle from the USA
- Thread starter DaveB
- Start date
- Thread starter
- #22
DaveB
Active VIP Member
Well ya. It's a street car.
- Admin
- #23
- Joined
- Oct 20, 2006
- Messages
- 39,540
- Reaction score
- 14,738
- Location
- Edmonton Alberta, Canada
- Website
- www.sledbunnyracing.com
Nice looking car.
- Thread starter
- #24
DaveB
Active VIP Member
1790km day and she is home. Left at 3:30am....home at 11.
HotShotHarry
Active VIP Member
Nice!
ferniesnow
I'm doo-ing it!
- Joined
- Dec 2, 2008
- Messages
- 108,852
- Reaction score
- 83,170
- Location
- beautiful, downtown Salmon Arm, BC
A fun toy for sure! Thanks for sharing.
DRD
Active VIP Member
Everything as you hoped it would be?
- Thread starter
- #28
DaveB
Active VIP Member
It’s waaay more “race” than “street”. The car is a California solid car, but it was painted to be a race deal, not a show car....its a “20 foot paint job”. Mechanically, it has a LOT of high buck parts. It will be fun.
DRD
Active VIP Member
Tomorrow when it's warm I'll hop on the bike and come over, we can start painting that nice new pavement in front of yer place with it.
brendon444
Active member
price?
- Thread starter
- #31
DaveB
Active VIP Member
neilsleder
Active VIP Member
Nice Dart!
- Thread starter
- #33
DaveB
Active VIP Member
...nuthin...
Last edited:
- Thread starter
- #34
DaveB
Active VIP Member
Well not sure if anyone is interested...but I’ve been playing.
Removed super-stock springs in favor of Calvert Racing split monoleafs and Cal Tracs. Removed a ton of crappy wiring...this is an ongoing project. Removed interior and welded holes in floor. Made NHRA legal belt mounts. Old belts were through sheet metal only...nfg. Hurst Quarter stick shifter and melted cable removed....TurboAction Cheetah installed with new mounts welded to floor instead of tex screws like the old shifter. Re-plumbed some N2O lines....but thinking about removing it. Now making cardboard templates for aluminum interior panels....
Removed super-stock springs in favor of Calvert Racing split monoleafs and Cal Tracs. Removed a ton of crappy wiring...this is an ongoing project. Removed interior and welded holes in floor. Made NHRA legal belt mounts. Old belts were through sheet metal only...nfg. Hurst Quarter stick shifter and melted cable removed....TurboAction Cheetah installed with new mounts welded to floor instead of tex screws like the old shifter. Re-plumbed some N2O lines....but thinking about removing it. Now making cardboard templates for aluminum interior panels....
Last edited:
DRD
Active VIP Member
Any garage burnouts?
- Thread starter
- #36
DaveB
Active VIP Member
Nope. It’s been apart a fair bit.
eclipse1966
Active VIP Member
gee Dave looks like we both have been busy! Getting car ready for body work, paint and new interior but had to take old engine out and put this beauty in with rebuilt tranny before the paint. Whole front end has been done as well. Enjoy your project!!
- Thread starter
- #38
DaveB
Active VIP Member
Getting the aluminum panels installed....
- Thread starter
- #39
DaveB
Active VIP Member
Re-done most of the wiring. Working on new dash...
DRD
Active VIP Member
You didn't doo anything silly like pull the funny gas off like you mentioned a few posts ago did you?
Similar threads
