2013 Ski-Doo Summit X800 etec
Pulled apart for a buddy
5000km on sled and motor (original top end)
Pulled apart to do top end (Preventative maintenance, sled ran flawless)
.0135" on the dial
.0024" is Max BRP spec
This pic is in a 180deg sweep
POSTING FOR BERNOFF!!!!!!!!!!!!
Does anyone know what causes the grooves to form in the faces of out clutches??? There was 3 sleds in our group all bought at the same time all driven relatively the same way, but this one seems to be creating grooves in the faces of the primary and the others...
just wondering if the 163 3" gets the same treatment when it comes to the lug spacing and weight loss (porting) that the 174 gets...
Any ideas or answers for a guy??
THanks guys/gals!!!!!!
Does anyone know IF BRP assessed the "Oil Tank Issue" for the 2014 sleds, or should we expect the little Aluminum Bracket to be there right from factory???
Asked the dealers when I picked my sled up from First Service and didn't get much of an answer....
What about other qwerks that 2014 has...
What has the Snow and Mud Nation used for polishing/ rubbing out MINOR scuffs and scrapes in the plastic on your sled????
Got some small "rashes" on the sled over the season, no real cuts or gouges.... But definately noticeable....
Some plastic is dull, some is polished shiny look..... What...
Probably better off asking this in the Xp forum cuz everyone is switching their XP's into T-motion, but my rear scissor to rails bolt on my 2013 XM seems really loose...
Does anyone know the actual torque specs for this bolt????
Ive been told snug and then a 1/4 turn by a few peole but would...
Anyone else notice the fuel level Gauge is "hit and miss" for a lack of a better term??? Or is it just due to the Huge air pocket that forms while filling up since the sled has such a rake to it.... sled says full when leaving gas pumps, but about 10 minutes later im down to 3/4 ( and that's...
How are your Exhaust mods working on the XM's?????
How many positives
How many negatives
How many people switched back
What are all your combinations (if you choose to unveil to the public)
Who all put a can on BEFORE the break in was done
Who waited till AFTER Break In???
I personally...
2013 Ski-Doo XM..... 800 etec......
Noticed that the rubber bushings that sit underneath of the exhaust have been subject to extreme heat, causing the rubber to disintegrate and fall apart (sled has only 300km's) also, noticed wiring protection and wiring directly behind the exhaust (by oil...
So the handlebars smoled a tree this weekend, tearing the reservoir off of the handle assembly.... I got a new one on the order, but need to know whats all entailed in bleeding the calipers....????
Do i need to take the Rotor cover off to get to the bleed screw????? What type of Fluid should I...
Recoil install.... Handle "cup" super hard to install..... Anyone else find this?
Installed PS on my ES etec..... Fount the hole in oil tank where recoil handle cup slides and locks into was too small....
Two hands and body weight could not get it to snap into place,was worried about cracking...
Just thinking about it here..... IF Rails get bent, do you think a person could upgrade rails to Ice-Age and still retain the T-motion??? Are Ice Age rails stiffer??? Will T-motion still function????
Comments??
Advice???
Platinum owners night I purchased a set of Rail reinforcements for my XM.... In the 2013 catalogue that they gave us they listed a part number that covers SP's XP\s and the Xm's.....
APPARENTLY THE part number listed in the book is the wrong one........ BRP had a second look at the kits after...
I sw this on my sled (2013 163 X) while installing new scratchers on my sled....
Notice in the pic that all sections with 2 paddles (2.5 Track) the outer edge of the paddles reach the outer edge of the track... BUT !....
Seems there is only one section of paddles (cycled through the whole...
Has anyone had issues or concerns about possibly voiding warranties after OR before installing these kits??? Don't think there would be an issue, but would like some outside opinions on this scenario....
Grip and rip Lower A-arm and Module Braces have an awesome reputation for saving the...
Has anyone had issues or concerns about possibly voiding warranties after OR before installing these kits??? Don't think there would be an issue, but would like some outside opinions on this scenario....
Grip and rip Lower A-arm and Module Braces have an awesome reputation for saving the sleds...
Picked up sled on Thursday night (thanks Martin Motorsports)... Put first tank of fuel in Saturday morning, headed out to make a few miles with my brother (Young-Gun) in the fields around my old stomping grounds..... WOW are these sleds wicked!!!!!!!! TOTALLY different animal than what I was...