Axys 800 Reliability

adamg

Active VIP Member
Joined
Mar 8, 2011
Messages
3,441
Reaction score
4,644
Location
S'toon,SK
I went to pick it up yesterday and got two different answers

1) (from the ownerof the dealer)the codes were too much brake and throttle and it was detonating, sometimes the ggb mtn cans cause this he said. He also said it should be okay after break in

2) I called the tech today that worked on it, he said the only code was brake/throttle and the can should not cause the sled to detonate or fall on its face

The sales guy and owner said they don’t add oil to these sleds as the sleds do that themselves in break in mode.

I plan to take her for a ride Saturday and recreate the problem, then take it back and leave it there until whatever electrical issue has been sorted.

Two words of wisdom:
1) Pin it to Win It.
2) If it can't take it it shall break.
 

takethebounce

Active VIP Member
Joined
Dec 10, 2008
Messages
5,193
Reaction score
8,750
Location
calgary
lol that’s too funny, I’ll take her for a abusive rip Saturday and report back haha

Put the stock can back on and if it does it when you put the cab on next time you can attribute it possibly to the can.
 

gdhillon

Active VIP Member
Joined
Sep 27, 2013
Messages
1,468
Reaction score
1,003
Location
Prince George
Took it for a rip at my buddies ranch after work yesterday. Got it up to 8300rpm, no codes. If I jammed on it fast it would sort of fall on its face but I’m thinking that’s just an elevation issue?

I’m happy that I didn’t get any more codes

It also isn’t a wheelie monster like everyone says they are, it doesn’t seem to be of control for me either...perhaps I just need more seat time to experience the playfulness?

It sure is easy to ride though, I love how nice it turns
 
Last edited:

Rene G

Active VIP Member
Joined
Dec 23, 2008
Messages
15,894
Reaction score
5,338
Location
Grande Prairie, AB
Took it for a rip at my buddies ranch after work yesterday. Got it up to 8300rpm, no codes. If I jammed on it fast it would sort of fall on its face but I’m thinking that’s just an elevation issue?

I’m happy that I didn’t get any more codes

It also isn’t a wheelie monster like everyone says they are, it doesn’t seem to be of control for me either...perhaps I just need more seat time to experience the playfulness?

It sure is easy to ride though, I love how nice it turns

Falling on its face is most likely a quick over rev, change up the weights and that should disappear.
 

adamg

Active VIP Member
Joined
Mar 8, 2011
Messages
3,441
Reaction score
4,644
Location
S'toon,SK
As I recall, the two weaknesses of the 800 Axys Pro generation:
-electrical relays fail, or the socket they plug into gets too dirty. Either way, bring spare relays and be prepared to swap them and clean the contacts. I never had this problem personally.
-exhaust temp sensor failure. Bring a spare. I had this problem, was able to limp sled home and buddy had a spare sensor in truck. Luckily I wasn't in an area that required full power to get back home.

From reading FB, in just the last week I've seen posts from Axys 800 owners with these specific item failures that make it very hard to get the sled back to the truck, much less ride the next day:
-exhaust temp sensor failure
-ski rubber
 

slededjr

Active VIP Member
Joined
Nov 25, 2011
Messages
1,577
Reaction score
1,972
Location
sherwood park
Agree with above.
once the exhaust sensor goes you’re pretty much fubar as it derates all power and can’t rev past 6700ish. Carry a spare sensor or at least carry a bypass for it.
 

Frankenytro

Active VIP Member
Joined
Oct 10, 2013
Messages
819
Reaction score
1,551
Location
Edmonton ab
Never heard of a bypass, does anyone know approximately how much resistance would be required to trick the ecm into thinking the pipe is hot?
 

slededjr

Active VIP Member
Joined
Nov 25, 2011
Messages
1,577
Reaction score
1,972
Location
sherwood park
I have quite a few left. It’s a inline resistor loop that takes place of the probe. Just unplug probe and plug this in.
0c49d31d9424de971b557289d8b8e3c5.jpg
 

slededjr

Active VIP Member
Joined
Nov 25, 2011
Messages
1,577
Reaction score
1,972
Location
sherwood park
Few pics posted above from turbo sled. The stock runs the same. Doing some more testing with mine as it has pipe and head.
 

Complexd

Active VIP Member
Joined
Dec 2, 2013
Messages
375
Reaction score
695
Location
Whitecourt
Been reading a bunch on here and talked to a few guys on the hill about the 850s being terrible for fouling plugs during break in. Thought it was just an 850 issue, sure enough chit chatted a guy last time I was out and he was on his 3rd set of plugs in 85km on his new 800. Same day mine (700ish km) started spittering and sputtering a couple times on the bottom end and cleared up as the RPMs came up. Would have to think just break mode over fueling and oiling and ill swap em out when its done (17 hours at 5000+ rpm) ? Anyone else having problems with 800s fouling?
 
Top Bottom