Camper Project

~Rowdy~

Active VIP Member
Joined
Dec 2, 2009
Messages
3,738
Reaction score
5,040
Location
Alberta
Here's my project this summer. :D :beer:

1985 Okanagan Camper - dimensions 8' wide, 13' tip to tail
Some minor water damage around some roof vents that leaked. Roof vents were replaced by previous owner before I purchased it. Fridge doesn't work. I haven't had a chance to look at the fridge yet to see if I can get it going.

IMG_0795.JPG

IMG_0799.JPG

IMG_0798.JPG

IMG_0796.JPG

IMG_0797.JPG

1978 Triple E Trailer - dimension of deck 7'7" wide x 16' long

Stripped down and turned into a flat deck. Completely re-structured, new bracing, welds, wood etc. Only issue is the break away battery connection which I will replace with a kit from Princess Auto. Nice and tall for clearance.

FullSizeRender.jpg


IMG_0883.JPG

The Plan

Mount camper 1ft from back of trailer centering the Center of Gravity of the camper over the center of the tires, or as close as possible. Building a dog run underneath the sleeper section. Half fully enclosed like a dog house with an access panel on the side, the other side slatted with chicken wire to allow air movement and my pup to see with an opening door.

Build locking storage underneath the sides for misc items.

Build a shedding roof for the winter on top so it won't collapse from the weight of snow. Not sure what I'm doing here yet. Waiting to see how the camper sits on the trailer.

Re-paint interior, re-upholster, replace flooring.

Where I'm At:

- Roof re-sealed using MS Detail
IMG_0836.JPG

- all seams, screws etc sealed with MS Detail
- inside cabinets and hardware torn down for painting
- new fabric selected for re-upholstery. This was horrible to shop for. I hate shopping but this was brutal, way too much to look at and they didn't have solid grey in an outdoor fabric...so I went the polar opposite way. Black for cushions and this funky print for curtains
19366196_10158868637150111_8054079735020694234_n.jpg
- This weekend I'll be lifting the camper onto the flat deck and mounting it down. I have several ideas of how to do this but so far these seem like the best two...Option A: Have a friend that's willing to crane it into place. Option B: 4, 3' tall sawhorses with 6, 4x4 10' long posts, place camper on this, drive trailer under, jack it up, pull posts and set it down.

Pretty stoked on this project. :)
 
Last edited:

whoDEANie

Active VIP Member
Joined
Feb 8, 2009
Messages
4,633
Reaction score
8,479
Location
Edmonton
If I recall, you converted a holiday trailer into a toy hauler a couple years back. Time for an upgrade or you just like doing these projects?
 

~Rowdy~

Active VIP Member
Joined
Dec 2, 2009
Messages
3,738
Reaction score
5,040
Location
Alberta
If I recall, you converted a holiday trailer into a toy hauler a couple years back. Time for an upgrade or you just like doing these projects?

I sold that when I gutted my house 2 years ago. I needed something to live in for 4 months and she wasn't up to par to stay in full time that long. Figured it was time to get a camper again.
 

~Rowdy~

Active VIP Member
Joined
Dec 2, 2009
Messages
3,738
Reaction score
5,040
Location
Alberta
So I'm lucking out and craning the camper on. Thanks to a friend! :beer:
 

Trashy

Super Moderator
Moderator
Joined
Nov 16, 2008
Messages
130,461
Reaction score
100,441
Location
Fort Macleod
Krista, is the Jeep yours too? Or just there, where you bought the camper?
 

~Rowdy~

Active VIP Member
Joined
Dec 2, 2009
Messages
3,738
Reaction score
5,040
Location
Alberta
Not mine but the guy who sold me the camper owns it. It's for sale I do know that if you are in the market. But how's your shifting with a bum shoulder? And how is that shoulder doing anyways?
 
Last edited:

~Rowdy~

Active VIP Member
Joined
Dec 2, 2009
Messages
3,738
Reaction score
5,040
Location
Alberta
Productive weekend painting. Need one more coat everywhere and then finish up a few spots then I'll be good to put doors and hardware back in. Picked out flooring and back splash too. Today is the day for craning it onto the flat deck, wish me luck! :/

19599022_10158928517735111_3469001046906506637_n.jpg

19601503_10158928517725111_392393307754994329_n.jpg

19554882_10158928517770111_7995663555241220132_n.jpg

IMG_0909.JPG
 

~Rowdy~

Active VIP Member
Joined
Dec 2, 2009
Messages
3,738
Reaction score
5,040
Location
Alberta
And she's on! Ratchet straps are just temporary until I can figure out the best way to fasten her down. Huge thanks to Brian, Ty & Calgary Crane!! :)

19642577_10158946594720111_205113923751251829_n.jpg

19656984_10158946594710111_3218839565350885671_n.jpg

19642332_10158946594730111_1056369842352391668_n.jpg
 

arff

Active VIP Member
Joined
Apr 21, 2009
Messages
139,155
Reaction score
55,015
Location
Leduc
I have seen this done. It will work great.
 

neilsleder

Active VIP Member
Joined
Oct 18, 2009
Messages
9,618
Reaction score
16,999
Location
Leduc Alberta

TylerG

Super Mod Geek
Administrator
Moderator
Joined
Nov 7, 2006
Messages
30,267
Reaction score
27,379
Location
Parkland County
Inside the cabinets bolt it down to the trailer. That way it's held on good and you will never see the bolts. Just make sure to go through a cross member
I was going to suggest the same but thru steel plates on both sides, 1 inside the cabinet and one underneath the trailer
 

~Rowdy~

Active VIP Member
Joined
Dec 2, 2009
Messages
3,738
Reaction score
5,040
Location
Alberta
Inside the cabinets bolt it down to the trailer. That way it's held on good and you will never see the bolts. Just make sure to go through a cross member

That is a fantastic idea. I will have to see if I can located the bracing underneath. I am boxing it in on the outside around the base of the camper to prevent shifting of any sort. I like that idea way better than using turn buckles on the exterior, just seems a little more solid.

I was going to suggest the same but thru steel plates on both sides, 1 inside the cabinet and one underneath the trailer

I like the idea of using steel plates as a type of washer. Great suggestion. I'll take a peek at that this weekend.

Krista here's a couple good videos on RV fridge repairs. Same ideas that I use for repairing customers trailers and campers.

Gas - https://m.youtube.com/watch?v=FCqiVqZx5k4

110 volt - https://m.youtube.com/watch?v=aArA8MBhQ3w

Give me a holler if you ever have any questions. My number is below. :beer:

Awesome!! Thank you so much, I may take you up on that if all else fails, lol. My skills are fairly limited for that kind of thing and if there's any electrical involved I won't touch it haha. Me and electrical are not friends.


Well on my way home to bringing the camper to a lumber yard I was a victim of hit and run. I was in the far right lane waiting to turn northbound onto Barlow Trail and I could see a woman had squeaked in behind me to make it through the intersection. I could tell she wanted to get in the other turning lane so I moved up a bit for her in hopes she could make it. Well as soon as the oncoming traffic cleared, she went to go into the other turning lane but she did not swing wide enough. She caught the passenger side of her car on the edge of the trailer and scraped it, I think to the back of her car. I figured she'd pull up beside me and we could figure out a spot to pull over to check everything out but nope! She kept going, made the light and I sat there in disbelief. Luckily there is zero damage to my trailer, but her car would be pretty damaged as I had a small hunk of it on my trailer so I decided to report it to the cops so she couldn't come back at me somehow. I'll be keeping my eye out for her as this can't be her first hit and run and it sure would be nice for her to get caught.

On the upside...my trailer is at the lumber yard awaiting the additions. :) Exciting! I'll work on cabinetry at home and try to get that all ready to go back in in the meantime. yay :beer:
 

Ronaha

Active VIP Member
Joined
Dec 11, 2015
Messages
1,606
Reaction score
3,038
Location
Narnia
Good placement! Back at n the day I busted my jacks off right before maylong,wasn't going to miss it so I backhoed the thing into the back of my truck......it worked ok....ish lol
 

Quadzilla700

Active VIP Member
Joined
Aug 12, 2007
Messages
529
Reaction score
103
Location
Churchbridge Sask
That is a fantastic idea. I will have to see if I can located the bracing underneath. I am boxing it in on the outside around the base of the camper to prevent shifting of any sort. I like that idea way better than using turn buckles on the exterior, just seems a little more solid.



I like the idea of using steel plates as a type of washer. Great suggestion. I'll take a peek at that this weekend.



Awesome!! Thank you so much, I may take you up on that if all else fails, lol. My skills are fairly limited for that kind of thing and if there's any electrical involved I won't touch it haha. Me and electrical are not friends.


Well on my way home to bringing the camper to a lumber yard I was a victim of hit and run. I was in the far right lane waiting to turn northbound onto Barlow Trail and I could see a woman had squeaked in behind me to make it through the intersection. I could tell she wanted to get in the other turning lane so I moved up a bit for her in hopes she could make it. Well as soon as the oncoming traffic cleared, she went to go into the other turning lane but she did not swing wide enough. She caught the passenger side of her car on the edge of the trailer and scraped it, I think to the back of her car. I figured she'd pull up beside me and we could figure out a spot to pull over to check everything out but nope! She kept going, made the light and I sat there in disbelief. Luckily there is zero damage to my trailer, but her car would be pretty damaged as I had a small hunk of it on my trailer so I decided to report it to the cops so she couldn't come back at me somehow. I'll be keeping my eye out for her as this can't be her first hit and run and it sure would be nice for her to get caught.

On the upside...my trailer is at the lumber yard awaiting the additions. :) Exciting! I'll work on cabinetry at home and try to get that all ready to go back in in the meantime. yay :beer:


Sorry to hear about the hit and run. I had mounted a truck camper on a trailer before just using the turnbuckles and found camper still moved around. Even started to pull a couple of the eye bolts from the camper frame. Even had 8 tie downs on trailer Finally bolted it through floor to trailer and closed in the sides and put doors so I could use it for storage. Was solid after that and no more damage to camper
 

~Rowdy~

Active VIP Member
Joined
Dec 2, 2009
Messages
3,738
Reaction score
5,040
Location
Alberta
Good placement! Back at n the day I busted my jacks off right before maylong,wasn't going to miss it so I backhoed the thing into the back of my truck......it worked ok....ish lol

oh man that is crappy timing! At least it worked enough to get you through May Long haha.

Sorry to hear about the hit and run. I had mounted a truck camper on a trailer before just using the turnbuckles and found camper still moved around. Even started to pull a couple of the eye bolts from the camper frame. Even had 8 tie downs on trailer Finally bolted it through floor to trailer and closed in the sides and put doors so I could use it for storage. Was solid after that and no more damage to camper

Thanks! I'm just glad she didn't do any damage. I thought for sure she at least took out a light. Well you are making my concern about the turn buckles very valid. I'm not sold on that being how I tie it down, but there isn't much cross bracing underneath and they only used 2x2's so I'm not sure how easy it'd be to try to bolt through the floor to that and through the trailer. I am also boxing the base of the camper in on the trailer. Using 2x4's it's bolted through the trailer and attached directly to the camper bracing underneath. That should help drastically with shifting.

I have underneath the sides of the camper boxed in already now for storage, which will help as well with moving. Underneath the sleeper portion I'm actually building a dog run for my pup Bails. I can't remember the exact dimensions but it will look something along these lines. Quite large and perfect for a dog her size. Probably could fit a couple dogs in it if I wanted.

Top View Shows a partition in the middle as half the dog run will be solid plywood for shelter and the other half will have a screened area in the middle for a breeze and allow her to look out.

IMG_0921.JPG

And yes...my dog is spoiled, lol.

IMG_0898.JPG
 
Last edited:

~Rowdy~

Active VIP Member
Joined
Dec 2, 2009
Messages
3,738
Reaction score
5,040
Location
Alberta
Question: Anyone here have an insurance company that will insure this redneck rig? My broker is telling me they will only insure the trailer, not the camper or anything else.
 

tex78

Active VIP Member
Joined
Feb 5, 2010
Messages
17,505
Reaction score
16,873
Location
DA Moose B.C
Question: Anyone here have an insurance company that will insure this redneck rig? My broker is telling me they will only insure the trailer, not the camper or anything else.
Camper through house insurance??

As a rider, that's what we used to do in alberta, for trailer mind you
 
Top Bottom