DieselDemon
Active member
got the plates and insurance renewed ... legal again sweet!!!
What did you do for your ATV today?
- Thread starter zeebs
- Start date
psullivan
Active VIP Member
tearing it down to powder coat it.
- Thread starter
- #83
zeebs
Active VIP Member
- Thread starter
- #84
zeebs
Active VIP Member
Well yesterday I went for a ride and buried it a few times and put it in the shop to thaw it off. I was reading on another forum lastnight about the roll pins coming out/breaking off of the drive shaft knuckles so I went out to check mine and sure enough two have moved and one had broke off but must have just been holding on by a little bit and the other one I didnt check due to all the location and all the snow. So today I am fixing!!!
munhoez
Active VIP Member
- Joined
- Jan 27, 2009
- Messages
- 4,395
- Reaction score
- 592
Did it grin back and say "yes give it to me?" lol
I bet the machine orgasmed, shot the rad cap off, squirted coolant all over floor, on machine, in new lift kit packaging.
racerfromhell
Active member
Did it grin back and say "yes give it to me?" lol
LOL yes it did! :d I cant even tell you what it did when it seen me pull the jack stands out :d
racerfromhell
Active member
Well after cleaning all the mess after showing it the kit, I went ahead and installed it. The fit was perfect and went in with two of us (you need the extra set of hands to install the front brackets) and 8 beers , app 3 hours at a very leasurely rate. I gained a full two inches, no cv bind, and firmed up the ride. No more bottoming out and I set the springs at the lowest setting. A nice option is the quick front sway bar disconnect. pull a pin on the bottom mount, swing it forward and it stores up under the front bumper. As you can see by the after shot that it even looks happier......:d and yes I need a new floor in the garage
, app 3 hours at a very leasurely rate. I gained a full two inches, no cv bind, and firmed up the ride. No more bottoming out and I set the springs at the lowest setting. A nice option is the quick front sway bar disconnect. pull a pin on the bottom mount, swing it forward and it stores up under the front bumper. As you can see by the after shot that it even looks happier......:d and yes I need a new floor in the garageAttachments
quadboy55
Active VIP Member
Looked at it, thought for a bit... Taking it to Rapid sometime next week for snorkels and going to order a 3" CATVOS lift with a 2.5" Rake.
Also I decided to sell 'em stocker tires that cometh' with the XP.
Also I decided to sell 'em stocker tires that cometh' with the XP.
rzrgade
Active VIP Member
A few update pics of the build...
rzrgade
Active VIP Member
a few more
- Thread starter
- #92
zeebs
Active VIP Member
looked at it and got pizzed off at the front end saging down. Going to order HD front springs tomorrow and make it look like something
. Going to order HD front springs tomorrow and make it look like something
Last edited by a moderator:
CrankShop910
Active VIP Member
Plowed swow again.
northern bear
RIP May 30,2022
Absolutely nothing myself cause I'm at work, but my kid bagged it up and down the drive pushing snow.
Brute Force Boy
Active VIP Member
rzrgade
Active VIP Member
Very nice , what kinda ground clearence now ?
Brute Force Boy
Active VIP Member
Should be 13-14" now, I was just over 11" with my 26" xtr's.
Open Season
Active VIP Member
Got busy and made and installed new puck board A arm gaurds front and back.
rzrgade
Active VIP Member
Got a little more done today with intake and snorkels done....
racerfromhell
Active member
nice
Similar threads
