Direction of coolant flow...

CUSO

Active VIP Member
Joined
Jan 21, 2007
Messages
4,767
Reaction score
5,495
Location
Edmonton
I bought a slightly used '16 T3 163 last winter, and noticed that the paint is peeling from the right side of the cooler. I noticed a chip in the paint when I bought it, but then one day I open trailered it in April to a Buddys place and the paint peeled on one side of the cooler..

I went to Martin's west and inquired, the girl at the front service desk went to the shop foreman to ask about it....

He said it was from "abuse and overheating" right off the bat... without even looking at it,,,,,

Now, with that answer, I was a bit skeptical, because how could hot water make an enamel paint peel like that?

Even before the possibility of: bad surface preparation... bad paint... etc, he just concluded this. Black eye for
MMS...

I went to riverside and the service rep actually said that it could be possible, but if I give him the serial number, and some pics, he could open up a file case to see what they can do.

if they consider it, they would have me bring the sled in and check if it was ever overheated..

My question: Which way does the coolant flow< Down the right side then back via the left?

I'll throw in some pics shortly.

M
 

lilduke

Active VIP Member
Joined
Sep 15, 2009
Messages
17,217
Reaction score
61,265
Location
Local
the paint pealed off the cooler on my 14 and it was never over heated. lots have had this problem.
 

sirkdev

Active VIP Member
Joined
Nov 2, 2008
Messages
3,100
Reaction score
4,929
Location
Stony Plain
The answer to your question is via an infared heat gun temp in vs temp out keep in mind thermostat location. Honestly the 20$ princess auto guns are sufficient for most people’s needs.
 

oler1234

Active VIP Member
Joined
Nov 20, 2008
Messages
3,592
Reaction score
5,976
Location
Calgary, AB & Golden, BC
^^^^ really? If don’t know don’t answer.


yes, throttle side is the “inlet”(hot side) if you will and brake side is the “outlet”(cold side)

that being said, a ton have this problem. Mine included.

You think that the coolant could get hot enough to lift powder coating? Doubt the motor would run after that heat soak. more likely bad paint or, bonding, or prep from the factory.
 

sirkdev

Active VIP Member
Joined
Nov 2, 2008
Messages
3,100
Reaction score
4,929
Location
Stony Plain
^^^^ really? If don’t know don’t answer.


yes, throttle side is the “inlet”(hot side) if you will and brake side is the “outlet”(cold side)

that being said, a ton have this problem. Mine included.

You think that the coolant could get hot enough to lift powder coating? Doubt the motor would run after that heat soak. more likely bad paint or, bonding, or prep from the factory.


Seriously? Have to trouble shoot these things every day. It comes back to basic mechanics. Temp in vs temp out.
 

LBZ

Active VIP Member
Joined
Apr 16, 2010
Messages
3,068
Reaction score
3,649
Location
Central Alberta
Seriously? Have to trouble shoot these things every day. It comes back to basic mechanics. Temp in vs temp out.

Ya that’s how I do it often also. I have a sweet snap on infrared camera temp gun. Very helpful in troubleshooting heat/cooling issues.
 

Bnorth

Active VIP Member
Joined
Dec 18, 2010
Messages
10,511
Reaction score
19,964
Location
Salmon Arm
^^^^ really? If don’t know don’t answer.


yes, throttle side is the “inlet”(hot side) if you will and brake side is the “outlet”(cold side)

that being said, a ton have this problem. Mine included.

You think that the coolant could get hot enough to lift powder coating? Doubt the motor would run after that heat soak. more likely bad paint or, bonding, or prep from the factory.
I thought they were painted not powder?

But yes I've seen it on lots of XM's it starts to lift in the grooves and peels off. Can't see it being from overheat likely from poor prep/adhesion.
 

CUSO

Active VIP Member
Joined
Jan 21, 2007
Messages
4,767
Reaction score
5,495
Location
Edmonton
Thanks all.

I might just get a colour match from Carlson and fix it myself..
 

treeboy

Active VIP Member
Joined
Nov 14, 2010
Messages
183
Reaction score
112
Location
The Monashee Mountains
Heat is not the problem, it’s brps pour as prep work before paint or powder coating. I’ve seen a lot of tunnels and coolers do that from them.
 

greenthumb

Active VIP Member
Joined
Mar 16, 2013
Messages
580
Reaction score
2,003
Location
Shuswap
Thanks all.

I might just get a colour match from Carlson and fix it myself..

Pretty much every one I've seen peels after a few years, mine included and it's never been overheated.

If I were fixing it, I'd look at getting a strip of black vinyl. Will give you some abrasion protection too.
 
Last edited:
Top Bottom