Order of assembly for torque arm (scissor)

Bogger

Bogger of the GBCA
Joined
Feb 21, 2007
Messages
24,413
Reaction score
18,488
Location
Down by the Bay
So I ripped into the wifes pro last night to change out the front torque (scissor) arm in the skid. I had been warned about the bolts spinning in the sleeve and thankfully the process I was advised to follow worked. Removal of the damaged part was pretty simple for a mechanically retarded individual such as myself.

Removed the front shock bolt, removed the footwell bolts leaving the top disconnected. Then I removed the rear shock bolt and the shock rod bolt and finally the long shaft bolt - Old part removed slick as snot.....

Put the new torque arm in and started with the upper front shock bolt and the footwell bolts because they are the most difficult to access (upper part of the skid) and actually went together quite easily.

Now the struggle begins

I can't get the skid lined up to install the long shaft bolt on the bottom. I'm able to bolt up the shock and shock rod no problem but cant get the shaft bolt lined up. I've tried raising the sled, lowering the sled, using ratchet straps to try and winch it into alignment and ultimately spent 2 hours sweating, cursing and busting open a shin from kicking the stupid machine.

All I can figure now is to remove the footwell bolts and put the lower shaft bolt in first but my fear then is I will never get the upper footwell bolts to line up, they are much trickier and come in from both sides as opposed to what should be a simple long bolt install.

Am I missing something? is there a trick to this? tourque arm.jpg
 

TylerG

Super Mod Geek
Administrator
Moderator
Joined
Nov 7, 2006
Messages
30,265
Reaction score
27,376
Location
Parkland County
So I ripped into the wifes pro last night to change out the front torque (scissor) arm in the skid. I had been warned about the bolts spinning in the sleeve and thankfully the process I was advised to follow worked. Removal of the damaged part was pretty simple for a mechanically retarded individual such as myself.

Removed the front shock bolt, removed the footwell bolts leaving the top disconnected. Then I removed the rear shock bolt and the shock rod bolt and finally the long shaft bolt - Old part removed slick as snot.....

Put the new torque arm in and started with the upper front shock bolt and the footwell bolts because they are the most difficult to access (upper part of the skid) and actually went together quite easily.

Now the struggle begins

I can't get the skid lined up to install the long shaft bolt on the bottom. I'm able to bolt up the shock and shock rod no problem but cant get the shaft bolt lined up. I've tried raising the sled, lowering the sled, using ratchet straps to try and winch it into alignment and ultimately spent 2 hours sweating, cursing and busting open a shin from kicking the stupid machine.

All I can figure now is to remove the footwell bolts and put the lower shaft bolt in first but my fear then is I will never get the upper footwell bolts to line up, they are much trickier and come in from both sides as opposed to what should be a simple long bolt install.

Am I missing something? is there a trick to this?View attachment 221832

did you tighten the upper bolts up all the way? if so loosen them off and then try to get it to line up, your process sounds like you're on the right path, it should like up fairly easily from there...... do not do up the shock until you're done the long bolt.
 
  • Thread starter
  • Moderator
  • #3

Bogger

Bogger of the GBCA
Joined
Feb 21, 2007
Messages
24,413
Reaction score
18,488
Location
Down by the Bay
did you tighten the upper bolts up all the way? if so loosen them off and then try to get it to line up, your process sounds like you're on the right path, it should like up fairly easily from there...... do not do up the shock until you're done the long bolt.

I can easily undo the shock bolt, but I need to be careful with the shock rod, when I lifted the tunnel that SOB fell through one of the track holes and it was a B!tch to get back out. I'll try loosening those footwell bolts and see how she goes... I was flying solo last night too, might get the wife to come out and give me a hand tonight....
 

firstdoo

Active VIP Member
Joined
Nov 21, 2013
Messages
721
Reaction score
1,620
Location
Stony Plain
How soon do you need to get it back together? I'm not a poo guy and haven't worked on what your doing but I could possible come give you a hand. (not mechanically retarded, lol. Not taking a shot, just saying I'm an Industrial Mechanic)
 
  • Thread starter
  • Moderator
  • #5

Bogger

Bogger of the GBCA
Joined
Feb 21, 2007
Messages
24,413
Reaction score
18,488
Location
Down by the Bay
How soon do you need to get it back together? I'm not a poo guy and haven't worked on what your doing but I could possible come give you a hand. (not mechanically retarded, lol. Not taking a shot, just saying I'm an Industrial Mechanic)

I appreciate the offer and if I can't get it back together tonight I may reach out for assistance.... I need this thing on the trailer headed to MM20 Friday morning. I should have had it done a long time ago but I got lazy....
 
  • Thread starter
  • Moderator
  • #8

Bogger

Bogger of the GBCA
Joined
Feb 21, 2007
Messages
24,413
Reaction score
18,488
Location
Down by the Bay
OK so the footwell bolts should be the last to go in then because they are what attaches the skid to the chasis.... That sucks because they were much easier to install with the sled sitting upright and I could wrench on both sides at the same time.

Oh well it is what it is
 

LUCKY 7

Active VIP Member
Joined
Jan 17, 2009
Messages
5,766
Reaction score
9,042
Location
Sparwood
I think this is the way to go because I saw a few times in a local Fernie shop everytime a pro/axys was in for a once going over the sled was on its side and the skid was out.
fully assemble the skid. lay sled on its side. install in chassis.
 
  • Thread starter
  • Moderator
  • #11

Bogger

Bogger of the GBCA
Joined
Feb 21, 2007
Messages
24,413
Reaction score
18,488
Location
Down by the Bay
DONE.... What a fawk around, suppose it would be easier if I had to do it again but no thanks.

Thanks for the direction folks - Snow is all cleared and sled is put back together, tomorrow we pack and load up to head west to MM friday morning.

Cheers
 

Rene G

Active VIP Member
Joined
Dec 23, 2008
Messages
15,894
Reaction score
5,338
Location
Grande Prairie, AB
DONE.... What a fawk around, suppose it would be easier if I had to do it again but no thanks.

Thanks for the direction folks - Snow is all cleared and sled is put back together, tomorrow we pack and load up to head west to MM friday morning.

Cheers

Glad you got her put back together, I’ll see ya at MM!
 
Top Bottom