Recent content by Backcountrypro

These Powder Freak drivers are buttery s-m-o-o-t-h!

I just did this mod to my 2019 850 with Redline turbo...very similar to Fred’s ride. I concur about the rolling resistance being noticeably less. 6 tooth next to 7 tooth here...

Up is down and down is up. The lower the cal number the higher the oil output. Mine was on 5 in stock form, and I had it is set to 2 when I installed my kit. This was per Daves instructions.

Back a ways in this thread I posted about the check valve I installed. Installing the check valve took care of my starting problem 100%. No negative effects to fuel pressure, it is maintained right at 42-44 psi. Sled now starts first pull, hot or cold. Just a FYI.

https://www.highflowfuel.com/i-23908469-quantum-inline-or-intank-high-flow-viton-fuel-pump-check-valve-8mm-5-16.html?gclid=CjwKCAiAoOz-BRBdEiwAyuvA6wCmuJRQG4Gu_D5TX5cLvcEdg-Aj3x-19tiycZKnykQCV0hhymrq3RoC4swQAvD_BwE I installed this as close to possible to the tank on the pressure hose...

I asked last season if you had any type of starting issue with your kit. I found out they are no longer removing the internal check valve from the pump housing. I purchased a high flow brass check valve from Quantum Fuel and installed it where the fuel pressure hose comes out of the pump. All...

Yes the new G3 HO box has a box with a small dial. This box controls the stock boost injectors plus the auxiliary injectors.

kingcat162 I have been using the Shelborne fuel additive for many years on my turbo sleds. I have had great luck with it and it sure simplified my fuel needs.

I had the same run around with my local dealer twice. First time was with my old 800 Etec turbo. I did a rebuild and I was told to have the break-in reset and since it was a turbo sled have the pump turned up. I had the service manual so I knew how to increase the oil consumption. The tech...

The higher the number the lower the amount of oil. I installed a Redline turbo on my 850 and part of the set up was taking it to the dealer and having the oil pump set at 2. It uses about 1/3 rd of the oil reservior to a full tank of fuel. If it were me I think I would ride it, maybe try to...

Fredw-Im going to keep following this. I’d like to do a Diamond S hood too so Id like to see what you come up with for a cold air intake. Also when you remove the factory airbox where do you move the temp sensor to? I thought I was told that sensor does both intake temp and barometric pressure...

Fred-Did you have any kind of a starting problem once the underhood temp was warmed up? I installed a used Redline HO kit on my 19. I had problems with it wanting to start once it was warmed up good, it was especially difficult to start if it sat for more than a few minutes. First start of...

Bryce will help you out. I had to have him "dumb it down a bit" for me at first but now that I have it figured out it is no problem. I haven't messed with the data logging features at all. I take my laptop with me on my tuning ride and I am usually able to get it dialed in how I like fairly...

I would have to disagree with that statement. The old Dobek or Attitude Industries fuel boxes were maybe 1980's tech but not the Redline controller. The Redline box is fully tunable by the end user, and it has datalog capabilities. I have ran a lot of fuel boxes over the years and the Redline...

Connect to box. Click down blue arrow. You should hear a beep once the map is loaded into the program. Click the "X" in the upper left hand corner to close the map on screen. Now go back and open "Table A". The map that appears is the one pulled from the box. From there maybe you can now...