Pipe and chip?

fastidle · 05-05-2009, 11:23 PM

Hey guys Im also looking at putting a chip and a pipe onto my 07 700 king quad and was wondering if anyone had some tips for the best performing ones, most power and the results you have seen.

QMAO · 05-05-2009, 11:36 PM

Fastidle, Hi and welcome to the site. I am not sure about pipes as I have a modded stock pipe, but the HMF is suppoesed to be about the best for pipes available for the KING.
As far as chips, the VDI is a very good ECM available.They are built right in Calgary and Lyle gives very good and personable tech support.
The VDI is the only ECM that controls both the fuel and the timing advance. It can also remove the rev limliters.Here is a link to the site for VDI Velocity Devices Inc. - Your source of high performance ATV parts and accessories.

fastidle · 05-06-2009, 12:28 AM

Thanks QMAO, I will check it out for sure. The VDI sounds good and it will get rid of my reverse limiter, thats HUGE

ttpowersports · 05-09-2009, 10:07 PM

i agree we sell lots of the copper heads from velocity and they are easy to install and truely the best bang for your buck

05-05-2009, 11:23 PM	#1 (permalink)
fastidle Member Join Date: May 2009 Location: red deer alberta Posts: 12 Casino Cash: $14700 Thanks: 0 Thanked 0 Times in 0 Posts No Classified Ratings	Pipe and chip? Hey guys Im also looking at putting a chip and a pipe onto my 07 700 king quad and was wondering if anyone had some tips for the best performing ones, most power and the results you have seen.

05-05-2009, 11:36 PM	#2 (permalink)
QMAO Member Join Date: Jan 2007 Location: Central,Alberta Posts: 176 Casino Cash: $358976 Thanks: 7 Thanked 39 Times in 31 Posts No Classified Ratings	Re: Pipe and chip? Fastidle, Hi and welcome to the site. I am not sure about pipes as I have a modded stock pipe, but the HMF is suppoesed to be about the best for pipes available for the KING. As far as chips, the VDI is a very good ECM available.They are built right in Calgary and Lyle gives very good and personable tech support. The VDI is the only ECM that controls both the fuel and the timing advance. It can also remove the rev limliters.Here is a link to the site for VDI Velocity Devices Inc. - Your source of high performance ATV parts and accessories. __________________ 2005 Suzuki King Quad 700, 27"x11" Zillas, VDI ignition, some other mods also!!

05-06-2009, 12:28 AM	#3 (permalink)
fastidle Member Join Date: May 2009 Location: red deer alberta Posts: 12 Casino Cash: $14700 Thanks: 0 Thanked 0 Times in 0 Posts No Classified Ratings	Re: Pipe and chip? Thanks QMAO, I will check it out for sure. The VDI sounds good and it will get rid of my reverse limiter, thats HUGE

05-09-2009, 10:07 PM	#4 (permalink)
ttpowersports Supporting Vendors Join Date: Dec 2008 Location: bonnyville alberta Posts: 717 Casino Cash: $652620 Thanks: 234 Thanked 287 Times in 180 Posts No Classified Ratings	Re: Pipe and chip? i agree we sell lots of the copper heads from velocity and they are easy to install and truely the best bang for your buck __________________ the only bad ride is the one you missed!!!! Visit Us Online At: http://www.ttpowersports.com

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Sponsored Links, Plese click on Banner to View there Website

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
800 EFI Chip?	redrum	ATV's	10	04-21-2009 10:35 AM
best chip for m7 ??	FossY	PERFORMANCE and MODIFICATION GARAGE	5	10-24-2008 12:21 AM
Info needed on coating pipe, y-pipe and can	Lanko	PERFORMANCE and MODIFICATION GARAGE	7	09-30-2008 02:07 PM
TFI/EFI chip	d jones	ATV's	5	04-06-2008 03:48 PM
chip	jeffso	JUST ABOUT ANYTHING GOES	5	03-29-2008 11:03 PM