 |  |  |
| | |
|
Discuss Rhino 660 Clutch kit/belt riding low in the ATV & DIRT BIKE RELATED DISCUSSIONS AND INFORMATION forums; Just replaced the internal clutch in my Rhino and did a clutch kit at the same time. The belt is ...
| ||||||
  |
| | LinkBack | Thread Tools | Display Modes |
10-16-2009, 09:28 AM
| #1 (permalink) |
| Member   Join Date: Nov 2006 Location: Stony Plain
Posts: 37
Casino Cash: $53855 Thanks: 6
Thanked 4 Times in 1 Post
 | Rhino 660 Clutch kit/belt riding low Just replaced the internal clutch in my Rhino and did a clutch kit at the same time. The belt is now riding about 3/4 to 1 inch lower than the top of the secondary sheave all the time. I'm sure it is supposed to be riding near flush to a bit above the secondary sheave and have had it apart a couple of times and it sits back in same spot. Anyone have this problem before? Any help would be great, I'm scratching my head at this one. Thanks.
__________________ 08 FX Nytro MTX, 08 Phaser MTX 98 Polaris 680 Ultra,93 Cat 580 EXT 06 Yamaha Rhino 660 07 Yamaha TTR 125 08 Yamaha V-star 1100 Clasic  |
|  |
| Sponsored Links, Plese click on Banner to View there Website | |
|
10-16-2009, 05:59 PM
| #2 (permalink) |
| Member  Join Date: Apr 2009 Location: Grande Prairie
Posts: 399
Casino Cash: $250660 Thanks: 25
Thanked 89 Times in 71 Posts
 | Re: Rhino 660 Clutch kit/belt riding low Your rollers aren't in properly in your primary, one must have fallen out of its groove. When you assemble the primary you have to hold it together so the rollers don't get sideways under the cam plate. Make sure your cam plate is on the output shaft splines, install the washer over the splines so it doesn't drop down and put the nut on.
__________________ 07 660 Rhino Save a horse, ride a cowboy. |
| |
| The Following User Says Thank You to AreWeThereYet For This Useful Post: | tayco (10-16-2009) |
|
10-16-2009, 11:05 PM
| #3 (permalink) |
| Member Join Date: Nov 2006 Location: Stony Plain
Posts: 37
Casino Cash: $53855 Thanks: 6
Thanked 4 Times in 1 Post
| Re: Rhino 660 Clutch kit/belt riding low Great, thanks for the info, i'll pull it apart and check it out. I thought it was something to do with the secondary new spring but that makes sense with the primary rollers. Off to the shop in the morning! 
__________________ 08 FX Nytro MTX, 08 Phaser MTX 98 Polaris 680 Ultra,93 Cat 580 EXT 06 Yamaha Rhino 660 07 Yamaha TTR 125 08 Yamaha V-star 1100 Clasic |
|
| |
|
10-18-2009, 08:22 PM
| #4 (permalink) |
| Member Join Date: Nov 2006 Location: Stony Plain
Posts: 37
Casino Cash: $53855 Thanks: 6
Thanked 4 Times in 1 Post
| Re: Rhino 660 Clutch kit/belt riding low AreWeThereYet, you were bang on the money! Pulled apart the primary and there she was, one roller sitting out of it's groove sideways. Put it together how you said and that belt is running perfectly where it should be! Thanks for your help! 
__________________ 08 FX Nytro MTX, 08 Phaser MTX 98 Polaris 680 Ultra,93 Cat 580 EXT 06 Yamaha Rhino 660 07 Yamaha TTR 125 08 Yamaha V-star 1100 Clasic |
|
| |
| Sponsored Links, Plese click on Banner to View there Website | |
| |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
| |
Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Chid Riding Belt | Trax 2 Treadz | Trax 2 Treadz | 1 | 09-04-2009 03:40 PM |
| Rhino clutch | toony | UTV's | 3 | 04-17-2009 11:26 PM |
| Noise in clutch on rhino | _Stevo_ | UTV's | 6 | 12-16-2008 06:40 PM |
| Problem with 08' 700FI Rhino Clutch | deanb | UTV's | 2 | 10-30-2008 10:20 AM |
| How to get rid of wet clutch on Rhino | _Stevo_ | UTV's | 1 | 08-12-2008 11:27 PM |
| All times are GMT -6. The time now is 11:47 PM. |
 |
Copyright © 2006 - 2009 SnowandMud.com
|  |
Linear Mode
