http://www.snowandmud.com/forum/ en Sat, 21 Nov 2009 00:01:47 GMT vBulletin 60 http://www.snowandmud.com/forum/images/snowandmud/misc/rss.jpg http://www.snowandmud.com/forum/ http://www.snowandmud.com/forum/f21/honda-rubicon-plastics-21365.html Wed, 18 Nov 2009 20:49:10 GMT Anyone had problem with fender plastics ripping? Seems way weaker than on my '03 450 S! ]]> fhe http://www.snowandmud.com/forum/f21/honda-rubicon-plastics-21365.html http://www.snowandmud.com/forum/f21/water-pump-leak-sportsman-800-a-21282.html Tue, 17 Nov 2009 17:11:20 GMT I just replace my water pump seal on my sportsman 800. I flushed the coolant and removed the overflow tank to find that it had 1/4 inch of mud in... I just replace my water pump seal on my sportsman 800. I flushed the coolant and removed the overflow tank to find that it had 1/4 inch of mud in the bottom. I going to route a breather hose to a higher spot so that it doesnt fill with mud again and take out another seal.I recomend to anyone with a coolant tank that sits that low to remove and check for mud. ]]> stealth 800 http://www.snowandmud.com/forum/f21/water-pump-leak-sportsman-800-a-21282.html http://www.snowandmud.com/forum/f21/02-03-polaris-700-how-they-21206.html Mon, 16 Nov 2009 17:10:40 GMT Hey, new here, l'm looking at a couple Polaris 700's, 02 and 03. I've had Pol sleds and know a few guys with 500 Polaris quads that have a ton of miles on them. What's the consensus on the older 700's?
Good motor, they were new in 02?
How does the carb do changing altitude?
Anything else to know about these in particuler?

Thanks ]]> Grit dog http://www.snowandmud.com/forum/f21/02-03-polaris-700-how-they-21206.html http://www.snowandmud.com/forum/f21/back-rest-20883.html Thu, 12 Nov 2009 02:00:36 GMT dose any one know if you can buy a back rest for a quad need something for my son to rest up against when he rides behind me on my trailboss dont... dose any one know if you can buy a back rest for a quad need something for my son to rest up against when he rides behind me on my trailboss dont want to put a box seat on as the are heavey. the polaris seat is long enough for the both of us with room to spare and he holds on to me so just need something behind him thanks. ]]> mavrick http://www.snowandmud.com/forum/f21/back-rest-20883.html http://www.snowandmud.com/forum/f21/very-strange-problem-yamaha-bruin-20761.html Mon, 09 Nov 2009 23:49:58 GMT i am having one of the weirdest problems ever with my bruin!!! youll be driving along and all of the sudden the atv will start studdering , you have... i am having one of the weirdest problems ever with my bruin!!! youll be driving along and all of the sudden the atv will start studdering , you have no power , and the reverse light turns on!!! but the bruin is still runnin!! does anyone know whats wrong?? has anyone had any problems like this on any atv??? anything helps!! please reply ASAP i need this atv all the time!! thanks:d. ]]> yamaha sx700 http://www.snowandmud.com/forum/f21/very-strange-problem-yamaha-bruin-20761.html http://www.snowandmud.com/forum/f21/arctic-cat-prowler-any-good-20527.html Thu, 05 Nov 2009 04:30:37 GMT what do you guys think of the arctic cat prowler? what do you guys think of the arctic cat prowler? ]]> arcticyam http://www.snowandmud.com/forum/f21/arctic-cat-prowler-any-good-20527.html http://www.snowandmud.com/forum/f21/seal-size-20517.html Thu, 05 Nov 2009 02:53:53 GMT Need the size or crossover Part Number for a crank seal for a 2001 Polaris 500 H.O.!! Need to order this tomorrow so I can have it Friday! Need the size or crossover Part Number for a crank seal for a 2001 Polaris 500 H.O.!! Need to order this tomorrow so I can have it Friday! ]]> PG2676 http://www.snowandmud.com/forum/f21/seal-size-20517.html http://www.snowandmud.com/forum/f21/04-yamaha-bruin-350-starting-problems-20340.html Mon, 02 Nov 2009 18:20:15 GMT hello , my dads 04 bruin 350 is having starting problems. usually when it gets wet , u go to start it , the neutral is on , then push the button it... hello , my dads 04 bruin 350 is having starting problems. usually when it gets wet , u go to start it , the neutral is on , then push the button it tics once and the light goes off , and then u half to pull it! does anyone know whats wrong and how to fix it? ]]> yamaha sx700 http://www.snowandmud.com/forum/f21/04-yamaha-bruin-350-starting-problems-20340.html http://www.snowandmud.com/forum/f21/aftermarket-660-grizzly-parts-20169.html Fri, 30 Oct 2009 14:51:18 GMT Hey everyone. I'm trying to find a good place to order aftermarket parts from US or Canada. The factory parts through yammie are sickly overpriced from what i've seen and I am doing all work myself. I am planning on replacing brake pads and rear axles (oversize) and also I would like to install a full snorkel kit. I've found quite a few stores on ebay but each one seems to specialize in one or two parts. I'd like to avoid huge shipping costs by buying everything from one place. Thanks for any info. ]]> tbosch http://www.snowandmud.com/forum/f21/aftermarket-660-grizzly-parts-20169.html http://www.snowandmud.com/forum/f21/660-grizz-studdering-20138.html Fri, 30 Oct 2009 01:09:33 GMT hello this is honus. just joined the site and was hopeing someone here could help me out !? i ride a 02 660 grizz and am having a problem. the last... hello this is honus. just joined the site and was hopeing someone here could help me out !? i ride a 02 660 grizz and am having a problem. the last ride it was on ran outstanding all day in and out of water and sand bars, then out of the blue would die. finally got it running again and got it back to the truck. found out it was from some crap in the carb.. not a big deal.. it also seemed to be running really hot but no temp lite. anyways took carb apart found some junk in there, put a new kit in it, and back on. started back up and exhaust gets really hot, really fast. (the firts four to five inches turn red), and it will pop or backfire through the intake. so back off with the carb for another cleaning, and i have had it off about 9 times now. also had tank off and cleaned, and instaled fuel filter. iv taken exhuast of to make sure nothing is pluged, and i have checked the vales. i know it running lean but im sure i have checked everything many times over. i have also checked for air leaks and nothing. wasnt sure if i could have a bad valve or whats going on. please help.. honus22 ]]> honus22 http://www.snowandmud.com/forum/f21/660-grizz-studdering-20138.html http://www.snowandmud.com/forum/f21/snow-blade-yfm-225-moto-4-a-19987.html Tue, 27 Oct 2009 21:08:47 GMT I've been trying to find a snow blade for my 1986 Yamaha YFM 225 Moto-4 with no success. I've contacted Yamaha Customer Relations but got little help. They said to buy a blade and have a machine shop make a custom mounting plate. I thought that maybe if the same frame was used on other models I could find a match that way but have heard nothing back from them yet regarding this. Is there anybody that has put a blade on an old Moto-4 or has any ideas that might help me out. Thanks. ]]> Big Bert http://www.snowandmud.com/forum/f21/snow-blade-yfm-225-moto-4-a-19987.html http://www.snowandmud.com/forum/f21/2008-suzuki-750axi-problem-19809.html Sat, 24 Oct 2009 16:54:26 GMT Alright i have had my atv for a week now and the other day i was out riding it and the brake or gear box felt like it was not engaging it was real... Alright i have had my atv for a week now and the other day i was out riding it and the brake or gear box felt like it was not engaging it was real sluggish in response. as soon as got it going it would snap out of it. Does anyone know what this could be.

Another problem i am experiencing is when i turn dif lock on it feels like the motor is cutting out like its not getting enough air or fuel it only does it when dif lock is on neone know what this could be. ]]> randolph http://www.snowandmud.com/forum/f21/2008-suzuki-750axi-problem-19809.html http://www.snowandmud.com/forum/f21/shifter-adjustment-19789.html Fri, 23 Oct 2009 22:10:08 GMT What is the proper way to adjust shift linkage on a 99 xplorer 400 thanks What is the proper way to adjust shift linkage on a 99 xplorer 400
thanks ]]> BOBANDTOBY http://www.snowandmud.com/forum/f21/shifter-adjustment-19789.html http://www.snowandmud.com/forum/f21/can-am-no-brake-lights-19731.html Thu, 22 Oct 2009 21:48:05 GMT Where do they get the power to run the brake lights. No power on the 20 amp fuse in the fuse box. Also because no brake light will not start in gear.... Where do they get the power to run the brake lights. No power on the 20 amp fuse in the fuse box. Also because no brake light will not start in gear. Help please Thanks ]]> Sledderglen http://www.snowandmud.com/forum/f21/can-am-no-brake-lights-19731.html http://www.snowandmud.com/forum/f21/rebuilding-86-honda-350-trx-engine-19705.html Thu, 22 Oct 2009 03:46:07 GMT Well, 23 years and 65,000 miles later, my tired old rattling 350 needs to be rebuilt as its low on compression and the timing chain and guides are... Well, 23 years and 65,000 miles later, my tired old rattling 350 needs to be rebuilt as its low on compression and the timing chain and guides are worn.

Just wondering if anyone else had torn one apart and rebuilt it, or at least replaced the timing chain and guides, etc.

Any response in regards to rebuilding or parts availability would be appreciated as Royal Distributing is limited to parts and having to find a piston and/or rings might be tricky. ]]> 4-Trax http://www.snowandmud.com/forum/f21/rebuilding-86-honda-350-trx-engine-19705.html