Disconnecting linkage pin?

Trashy

Super Moderator
Moderator
Joined
Nov 16, 2008
Messages
130,461
Reaction score
100,441
Location
Fort Macleod
So I got a repalcement leg for my evinrude 115 v4, this is probably the best video for remove and install.

But my question is, why does the linkage need to be removed? It's not like connected to anything moving
 

007sevens

Active VIP Member
Joined
Nov 24, 2009
Messages
20,955
Reaction score
16,974
Location
At my Place in Alberta
Im no expert Doug, but I believe the shift action is in the leg and one of the long rods that you see as he pulls the leg off. The pin he takes off would be the connection to that long rod to the transmission. My best guess.
 

cattechsummitrider

Active VIP Member
Joined
Nov 27, 2006
Messages
4,007
Reaction score
3,095
Location
sask
Im no expert Doug, but I believe the shift action is in the leg and one of the long rods that you see as he pulls the leg off. The pin he takes off would be the connection to that long rod to the transmission. My best guess.


You are very correct
 
  • Thread starter
  • Moderator
  • #6

Trashy

Super Moderator
Moderator
Joined
Nov 16, 2008
Messages
130,461
Reaction score
100,441
Location
Fort Macleod
I bought a used/rebuilt leg from Robins Marine in BC. I also watched a couple other vids and it makes sense now
 
  • Thread starter
  • Moderator
  • #8

Trashy

Super Moderator
Moderator
Joined
Nov 16, 2008
Messages
130,461
Reaction score
100,441
Location
Fort Macleod
Got the linkage pin out and now should be easy peasy.
Would also like thank my sponsor PBR :D
35fef0247faf99c01f8f8c0786dadf5b.jpg
 
  • Thread starter
  • Moderator
  • #11

Trashy

Super Moderator
Moderator
Joined
Nov 16, 2008
Messages
130,461
Reaction score
100,441
Location
Fort Macleod
Putting the linkage pin back in, is proving to be a major pita!!! Think I’ll have to call a friend for help tomorrow
 
  • Thread starter
  • Moderator
  • #12

Trashy

Super Moderator
Moderator
Joined
Nov 16, 2008
Messages
130,461
Reaction score
100,441
Location
Fort Macleod
Rebuilt leg is not putting water into the engine and out the telltale :rant:
Even too the leg off and sprayed water up the tube and it came out of the block
Put the leg back on again and still no water up :rant: :rant:

Thinking of putting the old leg on and seeing if it's an impeller issue?
 
  • Thread starter
  • Moderator
  • #13

Trashy

Super Moderator
Moderator
Joined
Nov 16, 2008
Messages
130,461
Reaction score
100,441
Location
Fort Macleod
Rebuilt leg is not putting water into the engine and out the telltale :rant:
Even too the leg off and sprayed water up the tube and it came out of the block
Put the leg back on again and still no water up :rant: :rant:

Thinking of putting the old leg on and seeing if it's an impeller issue?

Or I guess I could take the rebuilt one apart and see if it was assembled properly
 

cattechsummitrider

Active VIP Member
Joined
Nov 27, 2006
Messages
4,007
Reaction score
3,095
Location
sask
sounds like the rebuilt one hasn't been assembled properly, the waterpump impeller could be an old one and the fins might be inflexible or they forgot the key inbetween the shaft and impeller
images


Or you might not have the waterpump tube in the right place going into the motor
 
Last edited:

cattechsummitrider

Active VIP Member
Joined
Nov 27, 2006
Messages
4,007
Reaction score
3,095
Location
sask
don't bother putting the old one on

pm me your number if your having trouble and I will walk you through it,,,, but it might cost you some beer or vodka or rum if I ever see you LOL
 
  • Thread starter
  • Moderator
  • #16

Trashy

Super Moderator
Moderator
Joined
Nov 16, 2008
Messages
130,461
Reaction score
100,441
Location
Fort Macleod
sounds like the rebuilt one hasn't been assembled properly, the waterpump impeller could be an old one and the fins might be inflexible or they forgot the key inbetween the shaft and impeller https://encrypted-tbn0.gstatic.com/...zKQEgcixv7OnybpsAY9h_CXGwsa2Uv-WmxOu&usqp=CAU

Or you might not have the waterpump tube in the right place going into the motor

don't bother putting the old one on

pm me your number if your having trouble and I will walk you through it,,,, but it might cost you some beer or vodka or rum if I ever see you LOL
I'm pretty sure it the water pump missing the keyway. I'll drop the leg when I get home from work today and take apart the water pump.

I'll also send the company a text and let them know what's happening. $1100.00 for a rebuilt leg, I thought would include everything rebuilt.

If I have issues, I'll send you my number and would be happy to drink a bottle of rum one day with you, for your advice
 
Top Bottom