WeldCraft Jet

gunner3006 · Feb 18, 2020

neilsleder said:
If in and around the Leduc area before they go on I could tig that up for you! Might cost you a beer

Thanks Neil. I’m chapped cause I was down there back to back weekends.

gunner3006 · Feb 21, 2020

Busy week here. Got the new engine in yesterday. Starting to put everything back together. Cleaning up the electrical with a new fuse block and terminal strips. Got the stereo installed today and it sounds pretty good. I pulled my cooler apart and cleaned it with a de-scaler I use for work. It wasn’t horrible but I try to flush my system at home every time I pull it out of the water. I ended up having a buddy tig up my riser. He wanted to take a shot at it and see what he could do. He’s not a welder but he did a pretty decent job. Remote oil filter also got installed today. Coolant is back in and I was able to get my engine pre-lubed. It’s coming together.

gunner3006 · Feb 21, 2020

NoBrakes! · Feb 22, 2020

Good work man! Springs coming

gunner3006 · Feb 28, 2020

It’s alive

NoBrakes! · Feb 28, 2020

looks good man! Head up to Taylor and take her for a chew!

neilsleder · Feb 28, 2020

How much hp did you go up? Looks good!

gunner3006 · Feb 28, 2020

Just waiting for my pcv setup to show. Then it will be complete. As far as hp and torque it’s tough to say. Every chart and dyno I read is different. They there is the marine aspect. I think I’m safe to say pushing 350-375 ft/lb? The stroker was 440 I believe.

NoBrakes! · Feb 28, 2020

PCV right to flame arrestor no?

gunner3006 · Feb 28, 2020

NoBrakes! said:
PCV right to flame arrestor no?

Yup I’m just running thru one of those fiber cups that I can clean out.

NoBrakes! · Feb 28, 2020

man it would be nice if the risers had a dry port for pan evac into the exhaust....

gunner3006 · Mar 2, 2020

Got this bad boy installed today and lines run. Also got my diesel heater mounted. Just waiting for the new fuel tank to be built.

Chrisco · Mar 4, 2020

gunner3006 said:
//uploads.tapatalk-cdn.com/20200228/328892beb784f7c5288c89f4ecd7ee74.jpg

It’s alive

That looks great man !!! that extra length in them 2 plug wires is bothering me lol.

pfi572 · Mar 4, 2020

Chrisco said:
That looks great man !!! that extra length in them 2 plug wires is bothering me lol.

What about the screw clamps on exhaust ? Jeesh

gunner3006 · Mar 4, 2020

pfi572 said:
What about the screw clamps on exhaust ? Jeesh

Man that’s what was on there. And we’re those exhaust pipes a bitch to get off. Whoever fitted them did it tight.

NoBrakes! · Mar 4, 2020

pfi572 said:
What about the screw clamps on exhaust ? Jeesh

I have run a few lightings into hose with no clamps, what do you use?

pfi572 · Mar 4, 2020

gunner3006 said:
Man that’s what was on there. And we’re those exhaust pipes a bitch to get off. Whoever fitted them did it tight.

LOL

NoBrakes! · Mar 4, 2020

oh I see... anal

pfi572 · Mar 4, 2020

NoBrakes! said:
oh I see... anal

Just hacking on Chadd .

Looks awesome

Chrisco · Mar 4, 2020

pfi572 said:
Just hacking on Chadd .
Looks awesome

lol yes like i said looks wicked.

WeldCraft Jet

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Similar threads