Help.... lol rpm issues

ippielb

Active VIP Member
Joined
Mar 4, 2011
Messages
1,910
Reaction score
3,274
Location
SE Saskatchewan
Website
www.youtube.com
Check your grounds first off, second, take the ECU off, flip it over, give it a smell. Any burnt electronics smell means you gotta find a new one.

Also while you have the ECU off, make sure there’s nothing blocking the breather hose, or any condensation in the clean box underneath. When it freezes it will effect the barometric pressure sensor to compensate for altitude.

Verify the servomotor is cycling, have someone watch it when you start the sled up, it should cycle on start up.

If your servomotor doesn’t cycle, time to clean the power valves, check the connection to the servo, and possibly probe the wires to see if it’s getting 12v.

If your power-valves don’t open when they’re suppose it’s going to bog down and flood every time. Your sled is going to keep dumping in fuel as if they’re open.

One other thing, look on the side of the throttle body for your throttle position sensor, there should be a dab of paint on the screw that holds it on, and the sensor flange itself, if those aren’t inline. Then your sleds never going to run right. That’s what controls your fuel output, it tells the computer your throttle position to give out the right amount of fuel.
 

bgraff1

Active VIP Member
Joined
Oct 30, 2010
Messages
190
Reaction score
340
Location
Lloydminster Alberta
I had basically the same issue that killed two seasons of riding for me. one year I only made it 41.7km and was actually towed more km out then I made it under my own power. would run fine then all of a sudden would start bogging and my friends said it sounded like it was "moo'ing" lol. I checked everything, reeds, fuel pressure, fuel pickups, injectors etc etc etc. checked all the wiring I could and couldn't find anything. would think I fixed it, sounded fine and worked fine at home then drive 7hrs to ride and spend the whole time wrenching on it in the trailer. I was about ready to burn it. stator looked burnt but everything checked out as per cats diag tests. thought it as maybe the turbo i had on it so I removed all of that with no change. thought may it was the TPS so I performed many calibrations on it through my PCV with no change. TSS was never an issue would do it even if unplugged. I gambled on a used wiring harness and installed a new stator and its been trouble free the last 3 seasons. assuming it was the old harness as the stator checked out but who knows which one actually fixed it but very happy it is working again. this is on a non estart 2012
 

TROLLCAT

Active VIP Member
Joined
Nov 23, 2010
Messages
69,304
Reaction score
37,821
Location
Dease Lake BC
everything is testing good all with in spec
continuity is good threw the harness, ground side and power side
can't see any damage to wires

update have not frigger it out yet
 
  • Thread starter
  • Moderator
  • #49

catmando

Super Moderator
Moderator
Joined
Nov 7, 2006
Messages
8,964
Reaction score
6,372
Location
Edmonton
I’m trying too figure out who’s problems are all the suggestions for??
 
  • Thread starter
  • Moderator
  • #53

catmando

Super Moderator
Moderator
Joined
Nov 7, 2006
Messages
8,964
Reaction score
6,372
Location
Edmonton
Ok that was not the complete fix, Also found the coolant bottle warped and the cap would not seal losing all the anti freeze therefore overheating and having no pressure too circulate it throws it into limp mode . Thanks to my freind dale and t and t for supplying the parts hoping this is the last peice of the puzzle!
 

Clode

Active VIP Member
Joined
Jan 8, 2012
Messages
29,050
Reaction score
45,011
Location
BC
Ok that was not the complete fix, Also found the coolant bottle warped and the cap would not seal losing all the anti freeze therefore overheating and having no pressure too circulate it throws it into limp mode . Thanks to my freind dale and t and t for supplying the parts hoping this is the last peice of the puzzle!

my 2016 warped the bottle also, so I tried a lower pressure cap that I had and so far no issues, I think the cap I run now is a 13psi. I believe the stock ca was 16psi
 
  • Thread starter
  • Moderator
  • #55

catmando

Super Moderator
Moderator
Joined
Nov 7, 2006
Messages
8,964
Reaction score
6,372
Location
Edmonton
Picked up the sled last night, all good now but there was a whole bunch of reasons she ran like a cow, the coolant bottle was fawked , the reeds were fawked, the o rings in the head were fawked, the power valves were sticky as **** ....thanks too Dale for helping me out and clearing up all the issues, off too Golden this afternoon too give er the test run or 3 !
 

TROLLCAT

Active VIP Member
Joined
Nov 23, 2010
Messages
69,304
Reaction score
37,821
Location
Dease Lake BC
Picked up the sled last night, all good now but there was a whole bunch of reasons she ran like a cow, the coolant bottle was fawked , the reeds were fawked, the o rings in the head were fawked, the power valves were sticky as **** ....thanks too Dale for helping me out and clearing up all the issues, off too Golden this afternoon too give er the test run or 3 !



how many miles on it ?
 
  • Thread starter
  • Moderator
  • #58

catmando

Super Moderator
Moderator
Joined
Nov 7, 2006
Messages
8,964
Reaction score
6,372
Location
Edmonton
Need too do the clutch now, reving a little high
 
Top Bottom