SlimeR HDC Alpha

kanedog

Active VIP Member
Joined
Feb 3, 2015
Messages
3,141
Reaction score
8,615
Location
Kanedog 2015-2019, thanks for the good times S&M!
Thanks! Sled worked great, too bad we missed each other. Neck held up good, however my Knee not so much! Another year plagued with injuries for me I guess? SlimeR flipped over backwards on one of those whip flip re entry things and landed on my knee upside down pinned me and hyperextended my knee. Showed me who was the boss. Had me screaming like a little dyke biotch!!

That sux. Do you have vid with the screaming sound? I’m a bitch when I’m in pain also. Just a cold and I need chicken noodle soup and cuddles.
 

06 Dragon

Active VIP Member
Joined
Nov 17, 2006
Messages
2,006
Reaction score
3,333
Location
Red Deer County
Man that sucks E-Z. Hope you get healed up soon. How did she run and handle after all the work that you did?
 

E-Zmoke

Active VIP Member
Joined
Oct 12, 2008
Messages
1,515
Reaction score
2,751
Location
BC
Bizzump. Riding slimer or a new build this year?

Long story short my “hyperextended knee” from my one and only ride last year turned out to be a stage II tear of my ACL, PCL, and MCL as well as a broken femur!! Needless to say I never rode again last year.

It wasn’t for sale but I accepted a very healthy offer on SlimeR from a friend who knew I was out for the season just before the C19 started up and then the deal fell through a few short weeks later when C19 turned to be a thing. Which didn’t hurt my feelings one bit as I we had unfinished business together

My leg and knee feels pretty good now I’d say I’m a close 95%? I have a custom set of Mobius knee braces that I will be wearing this season

I will be running SlimeR again this year. I should prob get up to the shop and get it ready to go. Standby for updates. I have a few goodies that never ended up on the sled last year that I will be installing right away
 

E-Zmoke

Active VIP Member
Joined
Oct 12, 2008
Messages
1,515
Reaction score
2,751
Location
BC
Finally found some time to work on my sled today. SlimeR got a Powder Freaks Head, BDX Y-Pipe, Dalton weights, and a 2.5deg timing bump. The head is a piece of art. Super clean, fit and finish is 100% - Great quality product. I cant say the same about the BDX Y Pipe I was super disappointed with the quality. Spent a hour cleaning up the welds on the inside of the pipe, and getting it to fit properly. They did a good job at matching the 50mm cylinder port on the ctech cylinders though and is the reason why I went with this y pipe. It did clean up pretty good, after I got in there with the right tools, but for the price I feel this should have been cleaned up before sending out the door. All 3 Dalton weights were bang on 67g and profiles were smooth and cut proper as always. The stock Cat weights I took out are stamped 70g but 2 out of the 3 weighed 71g and the 3rd weight weighed 71.4g typical of cat though I’ve never had 3 weigh the same.

28c3111a694279ef5fccdb9aeb0ead46.jpg

1dcc8f5091686e80f3a00bfe07f4f080.jpg

f8158ef66ef4f098321e0e58da17f11a.jpg

198ac9961f64cd98e9533a6e1c60920c.jpg

03d6df655be5c35a7576ce68565c562f.jpg

6849f17c313c7052226b3a548180c04d.jpg

dae7fe3c88de312ecf53368cd670dd3d.jpg

260d176a8a1a6e5c3a9e4cf8b3015b56.jpg

4866f0545ab5e53f30decc6bd5e1d81a.jpg

10f5a9e9ae2f9513a76931d42784e32a.jpg
 

E-Zmoke

Active VIP Member
Joined
Oct 12, 2008
Messages
1,515
Reaction score
2,751
Location
BC
Looks great E-Z? Have you had SlimeR out this season? Just wondering how you like your barcode front end?

No lol not enough snow yet. Needs a couple more feet before I’ll be heading out.
 

tmo1620

Active VIP Member
Joined
Feb 28, 2008
Messages
3,765
Reaction score
7,079
Location
Whitecourt
Finally found some time to work on my sled today. SlimeR got a Powder Freaks Head, BDX Y-Pipe, Dalton weights, and a 2.5deg timing bump. The head is a piece of art. Super clean, fit and finish is 100% - Great quality product. I cant say the same about the BDX Y Pipe I was super disappointed with the quality. Spent a hour cleaning up the welds on the inside of the pipe, and getting it to fit properly. They did a good job at matching the 50mm cylinder port on the ctech cylinders though and is the reason why I went with this y pipe. It did clean up pretty good, after I got in there with the right tools, but for the price I feel this should have been cleaned up before sending out the door. All 3 Dalton weights were bang on 67g and profiles were smooth and cut proper as always. The stock Cat weights I took out are stamped 70g but 2 out of the 3 weighed 71g and the 3rd weight weighed 71.4g typical of cat though I’ve never had 3 weigh the same.

//uploads.tapatalk-cdn.com/20201205/28c3111a694279ef5fccdb9aeb0ead46.jpg
//uploads.tapatalk-cdn.com/20201205/1dcc8f5091686e80f3a00bfe07f4f080.jpg
//uploads.tapatalk-cdn.com/20201205/f8158ef66ef4f098321e0e58da17f11a.jpg
//uploads.tapatalk-cdn.com/20201205/198ac9961f64cd98e9533a6e1c60920c.jpg
//uploads.tapatalk-cdn.com/20201205/03d6df655be5c35a7576ce68565c562f.jpg
//uploads.tapatalk-cdn.com/20201205/6849f17c313c7052226b3a548180c04d.jpg
//uploads.tapatalk-cdn.com/20201205/dae7fe3c88de312ecf53368cd670dd3d.jpg
//uploads.tapatalk-cdn.com/20201205/260d176a8a1a6e5c3a9e4cf8b3015b56.jpg
//uploads.tapatalk-cdn.com/20201205/4866f0545ab5e53f30decc6bd5e1d81a.jpg
//uploads.tapatalk-cdn.com/20201205/10f5a9e9ae2f9513a76931d42784e32a.jpg
I found the same with my bdx y pipe, was very disappointed in the quality of craftsmanship, id expect that from a cheaper brand like d&d but cmon, take the extra half hour and make your product how it should be, i spent about an hour doing the same as you
 

Bnorth

Active VIP Member
Joined
Dec 18, 2010
Messages
10,510
Reaction score
19,964
Location
Salmon Arm
Been considering the same mods. I put the Y-pipe on already and have a timing key on the bench. Pickup up some clutching this week and hoping I'll be happy with that or I am looking at Duane's head as well.
 

Bodie319

New member
Joined
Dec 22, 2018
Messages
1
Reaction score
2
Location
Fernie
What are you guys trying to get for RPM with the BDX Y-Pipe? Mine came with a note to try to run around 7900, but I'm skeptical.
 

Bnorth

Active VIP Member
Joined
Dec 18, 2010
Messages
10,510
Reaction score
19,964
Location
Salmon Arm
What are you guys trying to get for RPM with the BDX Y-Pipe? Mine came with a note to try to run around 7900, but I'm skeptical.
I'm aiming higher. On the old flash my Alpha ripped hardest around 8250. I had to get the new flash when they replaced my motor so I'll see where it likes to be.
 

E-Zmoke

Active VIP Member
Joined
Oct 12, 2008
Messages
1,515
Reaction score
2,751
Location
BC
I’ll be aiming for 8100 with the timing bump, I’m hoping with the timing bump it will move that peak HP up a little bit. The head and the y pipe both make most of there gains in the mid range. I don’t want the peak HP to fall early before 8000 is my reasoning on the timing bump. I’m guessing that’s why BDX says to run at 7900 because the HP falls off the curve at that point? The only true way to find out is to get this combo on the dyno which I do have intentions of getting it on the PowderFreaks dyno as soon as I get some time to get it out there. Most of the dyno runs I’ve seen on the ctech peak HP is 8100-8200 stock, and then drops down to 8000-8100 with a pipe/head combo, head dyno run was 8000 peak and then drops even more with just a y pipe down to 7900. I’ll report back when I get it on the snow but for now I clutched for 8100 I set my weights at 73.3g for a base starting point and will fine tune from there. Hoping between the 3 it should have enough gains to pull 3g’s heavier...hoping to get it out soon to see what she can do
 

Dawizman

Active VIP Member
Joined
Feb 24, 2014
Messages
2,821
Reaction score
9,991
Location
Cold Lake, AB
I’ll be aiming for 8100 with the timing bump, I’m hoping with the timing bump it will move that peak HP up a little bit. The head and the y pipe both make most of there gains in the mid range. I don’t want the peak HP to fall early before 8000 is my reasoning on the timing bump. I’m guessing that’s why BDX says to run at 7900 because the HP falls off the curve at that point? The only true way to find out is to get this combo on the dyno which I do have intentions of getting it on the PowderFreaks dyno as soon as I get some time to get it out there. Most of the dyno runs I’ve seen on the ctech peak HP is 8100-8200 stock, and then drops down to 8000-8100 with a pipe/head combo, head dyno run was 8000 peak and then drops even more with just a y pipe down to 7900. I’ll report back when I get it on the snow but for now I clutched for 8100 I set my weights at 73.3g for a base starting point and will fine tune from there. Hoping between the 3 it should have enough gains to pull 3g’s heavier...hoping to get it out soon to see what she can do
I'm running the y-pipe with PEFI reflash and the SSI clutch kit. 73.1g seems to be working well for me at the moment, although I discovered that my munster throttle and CFR bars with ODI grips and cork under the heaters made it so I wasn't hitting WOT when I hit the bars. I won't know until the next trip to the hills how much more RPM and track speed I'll see after tightening that up.
 

E-Zmoke

Active VIP Member
Joined
Oct 12, 2008
Messages
1,515
Reaction score
2,751
Location
BC
I'm running the y-pipe with PEFI reflash and the SSI clutch kit. 73.1g seems to be working well for me at the moment, although I discovered that my munster throttle and CFR bars with ODI grips and cork under the heaters made it so I wasn't hitting WOT when I hit the bars. I won't know until the next trip to the hills how much more RPM and track speed I'll see after tightening that up.

Awesome great to know I wasn’t too far off with my 73g guess, do you know if the PEFI flash adds timing? I’m going to guess it does? What are your RPM’s with the 73g’s in?
 

Dawizman

Active VIP Member
Joined
Feb 24, 2014
Messages
2,821
Reaction score
9,991
Location
Cold Lake, AB
Awesome great to know I wasn’t too far off with my 73g guess, do you know if the PEFI flash adds timing? I’m going to guess it does? What are your RPM’s with the 73g’s in?
I'm not entirely sure on the timing. I bought the sled with the ECU reflash. I just reached out to precision EFI to get more info. They claim target rpm is 7900 and the tuning adds 8hp.

I honestly wasn't paying enough attention to notice the peak RPM this weekend. Was having too much fun. All I know is that it felt great, and was pulling better than the stock machines in the group.

My wife and I will be out in 2 weeks, and I'll be able to test better then. We have identical machines, except hers is stock. I could feel an immediate difference between the two last weekend when we were out together, but there was too much powder in McBride to see the gauges.
 

Slamnek

Active VIP Member
Joined
Nov 14, 2006
Messages
2,826
Reaction score
1,570
Location
Kitscoty
My 18 mountain cat was screaming hard at 8100-8200 before the latest cat flash and now it’s a dog at 7900-8000. I’m hoping the pefi flash gets me back to that 8100-8200 range.
 

Dawizman

Active VIP Member
Joined
Feb 24, 2014
Messages
2,821
Reaction score
9,991
Location
Cold Lake, AB
My 18 mountain cat was screaming hard at 8100-8200 before the latest cat flash and now it’s a dog at 7900-8000. I’m hoping the pefi flash gets me back to that 8100-8200 range.
Precision EFI says the ideal engine speed is 7900 with their tune, and that you should adjust clutching for that.
 
Top Bottom